|
Size: 3114
Comment:
|
Size: 2654
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 5: | Line 5: |
| * Type B Past Week Summary * Fabian took photos of the cleanroom in the ATC to help decide whether it is a good place to assemble PIs for Type A/B. * Hirata-san ordered and received wire for the BS and RM (will be cleaned 7/19). * Hirata-san received remachined locking parts for the IM (will be cleaned 7/19). * Hirata-san ordered additional Misumi parts to be used with the IM locking parts. * Fabian and Hirata-san weighed the masses that they've been constructing in the cleanroom and found a 600 g discrepancy from the Inventor (too light) for the IM. * Hirata-san ordered a medium-capacity scale to weigh the masses of the individual parts more precisely. * Hirose-san and his team successfully removed the misglued prisms from the dummy BS. * Fabian travelled to Kashiwa and removed most of the glue from the face of the dummy BS (where the flags had been). There is still some adhesive remaining on both the face and barrel, which will require more work and a second trip. * Shoda-san took a suitable segment of geophone noise data for analysis. Fabian will track down the calibration factors. |
* Type B Past Week Summary - weeks of 8/22 and 8/29 * Fabian, Mark, Zhao-kun and Yokogawa-kun did BS installation at Kamioka: * Weighed the BF, SF and dummy BS (in mirror box). * Moved the geophones onto the optical table, clamped them down and took another time series for analysis. * Aligned the IM, installed the extra trim masses, tested the picos and weighed the whole assembly. * Placed vacuum flanges and cleaned D-Sub cables ready for routing to the rack. * Realigned and immobilized the optical table (which had been bumped). * Made safety improvements on the second floor (new safety rail, new arrangement of floor pieces, caution tape around holes) * Suspended the dummy BS. Currently however it is not hanging correctly, but is off in the +Y direction by several mm relative to the mirror box. * We set up the BS OL, using one of the wheeled chests of drawers as a base and using the OL breadboard from the PR2 assembly frame. * Hirata-san made a 3D assembly model for SR2 and added the optical design. * Hirata-san worked with Uchiyama-san to solve the 90° rotation problem. It turns out the "box" part with the pistons can be rotated, so we can build the SR2 according to the original design. * Hirata-san investigated the puzzle of the BF-IM maraging rods, where the 2D drawings and 3D CAD do not agree. Fortunately the actual parts seem to agree with the 3D CAD. * Hirata-san washed 3 OSEMs (last of initial 10 for BS) and parts for two BFs (for Type A). He moved the BF parts into the clean room and will assemble them with ATC staff from next Wednesday 9/7. |
| Line 16: | Line 20: |
| * OSEMs * Akutsu-san is working to get wide-mouth OSEMs * Longer cables for BF->PI and SF->PI. * Connectors RECEIVED, cables being made. * SR machining test ongoing. * Lower breadboard stuff * Installation to be incorporated into the procedure document. Mark/Takahashi to discuss. * Breadboard springs (in manufacture, expected end of July) * Nail-head parts - RECEIVED. * Documents * BS Assembly Procedure [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=4235| E1504235]], [[https://onedrive.live.com/redir?resid=D5CCFA70A378E0D0!195&authkey=!AM_usynuo9QI57g&ithint=folder,webloc|E1504235 draft]] * To-do list during Mark's vacation * Apply grease to jacks for assembly frame (Takahashi) * Finish assembly of BS IM, RM and IRM (Fabian). * Weigh IM/RM/IRM (Fabian, Hirata) * Pack/ship IM/RM/IRM to Kamioka (Hirata/Fabian). * Analyze geophone data (Mark, Shoda) * Remove glue from dummy BS face (Fabian) * Remove prism from dummy BS (Hirose, Fabian?) * Reglue flags and prisms (Tatsumi, Fabian) * Buy wire for BS and RM (Hirata) * Clean wire for BS and RM (Hirata) * Do fit/function test of winches (Fabian/Hirata) * Ship winches to Kamioka (Hirata/Fabian) |
* Longer cables for BF->PI and SF->PI - RECEIVED * Longer term to-do list * Decide position of BS rack - DONE * Do Inventor assembly for SR2 in chamber and on assembly frame (Hirata) - ONGOING. * Write more of payload assembly procedure (Fabian) - ONGOING * Write more of BS Assembly Procedure [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=4235| E1504235]], [[https://onedrive.live.com/redir?resid=D5CCFA70A378E0D0!195&authkey=!AM_usynuo9QI57g&ithint=folder,webloc|E1504235 draft]] (Mark) - ONGOING * Lower breadboard installation to be incorporated into the procedure document. |
| Line 41: | Line 28: |
| * Do Inventor assembly for SR2 in chamber and on assembly frame (Hirata) * Apply vacuum grease to jacks for BS assembly frame (Takahashi) * Write more of payload assembly procedure (Fabian) * Write more of main assembly procedure (Mark) * Longer term to-do list |
|
| Line 48: | Line 30: |
| * Redesign SRx IM wire clamps for larger prisms, remachined RMs. | * Redesign SRx IM wire clamps for larger prisms, remachined RMs |
| Line 51: | Line 33: |
| * Check SR RM machining test progress (Hirata) |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
- Type B Past Week Summary - weeks of 8/22 and 8/29
- Fabian, Mark, Zhao-kun and Yokogawa-kun did BS installation at Kamioka:
- Weighed the BF, SF and dummy BS (in mirror box).
- Moved the geophones onto the optical table, clamped them down and took another time series for analysis.
- Aligned the IM, installed the extra trim masses, tested the picos and weighed the whole assembly.
- Placed vacuum flanges and cleaned D-Sub cables ready for routing to the rack.
- Realigned and immobilized the optical table (which had been bumped).
- Made safety improvements on the second floor (new safety rail, new arrangement of floor pieces, caution tape around holes)
- Suspended the dummy BS. Currently however it is not hanging correctly, but is off in the +Y direction by several mm relative to the mirror box.
- We set up the BS OL, using one of the wheeled chests of drawers as a base and using the OL breadboard from the PR2 assembly frame.
- Hirata-san made a 3D assembly model for SR2 and added the optical design.
- Hirata-san worked with Uchiyama-san to solve the 90° rotation problem. It turns out the "box" part with the pistons can be rotated, so we can build the SR2 according to the original design.
- Hirata-san investigated the puzzle of the BF-IM maraging rods, where the 2D drawings and 3D CAD do not agree. Fortunately the actual parts seem to agree with the 3D CAD.
- Hirata-san washed 3 OSEMs (last of initial 10 for BS) and parts for two BFs (for Type A). He moved the BF parts into the clean room and will assemble them with ATC staff from next Wednesday 9/7.
- Fabian, Mark, Zhao-kun and Yokogawa-kun did BS installation at Kamioka:
- Type B ongoing issues
Longer cables for BF->PI and SF->PI - RECEIVED
- Longer term to-do list
- Decide position of BS rack - DONE
- Do Inventor assembly for SR2 in chamber and on assembly frame (Hirata) - ONGOING.
- Write more of payload assembly procedure (Fabian) - ONGOING
Write more of BS Assembly Procedure E1504235, E1504235 draft (Mark) - ONGOING
- Lower breadboard installation to be incorporated into the procedure document.
- Work on BS simulation (Fabian)
- Do BS Simulink model (Mark, Kokeyama)
- Do 2D drawings of SR2 parts (Hirata)
- Redesign SRx IM wire clamps for larger prisms, remachined RMs
- Order SRM/PRM parts (Hirata/Shoda)
- Order SRx fasteners (Hirata)