|
Size: 4313
Comment:
|
Size: 2036
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 5: | Line 5: |
| ==== Report for the week of 3/11 ==== * Fabian helped Fujii-kun with the PRM most of the week. Hirata-san also helped at various times. * Fabian monitored the SRM yaw drift. It gradually reversed but so far remained small. We will try resetting it to zero with the pico and see if the trend changes. * Mark and Hirata-san debugged the BS: * We inspected the payload section and quickly found the problem: two RM EQ stops were touching, on the +L (-X,+Y) side at the top. This was probably because the stops had been adjusted with the IP unlocked and sitting a few mm to -L, whereas now we have the DCCTRL running and have been locking the IP at the LVDT zero. We drove the IP to L=+1.5 mm as a near-worst case, and backed off all the stops to give several mm of margin. Then we zeroed the IP pitch, roll and yaw with the picos. * We also opened the top of the BS and confirmed that the mechanical zero defined by the locking mechanism agreed with the LVDT zero. It was very close in L and T, but -728 µrad in Y, driven mostly by a -805 µm offset in H3. That much is probably not a dumb error but just a difference in technique among the three people using calipers to take data for the calibration. * We then prepared the BS for close-up: * We wiped and inspected the O-ring for the lid and replaced the lid. * We wiped all accessible surfaces in the lower half of the tank, rescued some dropped items (some PEEK tube and a small nut) and un-immobilized the LBB. * After all the above, the OL was a bit off-center but still on the QPD, and Nagano-san fairly quickly recovered the original alignment. * Terrence rebuilt the BS TILT OL according to a new layout suggested by Simon, which avoids scrambling the pitch/yaw at the first steering mirror and greatly reduces the amount of diagonalization required. He started on the LEN OL, but unfortunately the QPD stage fell and bent the brackets holding two of the micrometers. It's useable but we haven't installed it yet. * Terrence noticed some anomalous cross coupling on the SR2 (but not the SR3) and we investigated. * We suspected it might be an odd position of the beam spot on the optic, so we took pictures through the camera and LED viewports of SR3, and opened the SR2 tank and used a white target, but the beam spots were in very similar positions - close to central vertically and about 3 cm to the left of center horizontally. * We suspected it might be something touching at the IRM (because the IM OSEM TFs were fine), so we checked using a stick mirror with the IP centered, but all EQ stops were well backed off. * We suspected it might be a ghost beam from the LEN/TILT beamsplitter (and one was clearly visible on the SR2 TILT QPD) so Terrence set up a beam block, which improved things slightly but not completely. * Finally Terrence discovered that the problem was mainly uneven sensitivities of the QPD quadrants, and devised a new calibration procedure which allowed for it. Later we discovered that one of the 3 dB gain stages on the whitening filter was engaged, even though the switch on the BIO Config card was not. It mysteriously came good after we removed and replugged the BIO Config card. * Enzo and Terrence did a health check of the SRM and it was fine except for some apparent electrical noise around 240 Hz. They put in a low-pass filter to get rid of it for now. ==== Plan for week of 3/18 ==== * Mark, Fabian, Terrence at Kamioka full week. * More OL stuff. * SRM OL setup. * Recalibration of all OLs per new procedure. * Improve mounting of BS OL RX breadboard. * Reinstall BS LEN OL. * SRM controls and Guardian. * Reset SRM yaw and continue monitoring yaw drift. * Length/pitch decoupling. * Assist with pump down. |
==== Report for the week of 4/1 ==== * Support of Type Bp * Hirata-san procured the jigs for PRs and Takahashi-san tested one at TAMA. * Hirata-san cleaned up the flags for PR2 and Mark did the one for PRM. * Fabian helped Fujii-kun and Takashashi-san to reglue the flags. * Mark did a lot of maintenance on the MEDM screens: * Made the name of the suspension more obvious (no yellow text!). * Added rack temperature indicators. * Fixed the labels in the ADC screen (to reflect the LEN OL moving from ADC#0 to #1). * Fixed broken links. * Committed files to the SVN. * Mark did maintenance on the Guardian to make it give more helpful messages in the TRIGGER state. Formerly it only checked the user model watchdog and the coil driver watchdog, not the DACKILL, and gave the same generic notification for both. Now it checks all three and tells the user which need attention. * Mark tidied up the cables in the SR2 rack and returned a large pile of no-longer-used cables to the tent. * Mark started a !HealthCheck page on the Operation Manual wiki. Fabian and Mark ==== Plan for week of 4/8 ==== * Mark, Fabian at Kamioka Mon-Fri. * Help with Type Bp. * Health checks on Type B. * Monitor pumpdown. |
| Line 37: | Line 26: |
| * Modify RT models and/or Guardian to revert to the SAFE state under control in all but the most extreme emergency situations (rather than suddenly shutting off all output). | |
| Line 38: | Line 28: |
| * Throw out foil and other garbage. | |
| Line 41: | Line 30: |
| * Pull out unused cables in cable tray near SR3. * Return all unused cables to tent. * Tidy up cables in rear of SR2 rack. |
==== Plan for week of 4/15 ==== * Mark at Mitaka 4/15, Kamioka 4/16-18, f2f 4/19. * Fabian at Kamioka 4/15-18, f2f 4/19. |
| Line 46: | Line 36: |
| * Enzo at JPS then final vacation, 3/13-29 * Terrence's last day, 3/29. |
* Mark at Mitaka 4/15. * f2f 4/19 (Friday), 4/20, 4/21. * Terrence's next visit from 4/18. * Fabian's vacation 4/26 to 5/10. * Mark's vacation from about 5/22 to 6/11. * Mark's final day 6/28. |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Report for the week of 4/1
- Support of Type Bp
- Hirata-san procured the jigs for PRs and Takahashi-san tested one at TAMA.
- Hirata-san cleaned up the flags for PR2 and Mark did the one for PRM.
- Fabian helped Fujii-kun and Takashashi-san to reglue the flags.
- Mark did a lot of maintenance on the MEDM screens:
- Made the name of the suspension more obvious (no yellow text!).
- Added rack temperature indicators.
- Fixed the labels in the ADC screen (to reflect the LEN OL moving from ADC#0 to #1).
- Fixed broken links.
- Committed files to the SVN.
- Mark did maintenance on the Guardian to make it give more helpful messages in the TRIGGER state. Formerly it only checked the user model watchdog and the coil driver watchdog, not the DACKILL, and gave the same generic notification for both. Now it checks all three and tells the user which need attention.
- Mark tidied up the cables in the SR2 rack and returned a large pile of no-longer-used cables to the tent.
Mark started a HealthCheck page on the Operation Manual wiki.
Fabian and Mark
Plan for week of 4/8
- Mark, Fabian at Kamioka Mon-Fri.
- Help with Type Bp.
- Health checks on Type B.
- Monitor pumpdown.
- Work on Type B paper.
- Modify RT models and/or Guardian to revert to the SAFE state under control in all but the most extreme emergency situations (rather than suddenly shutting off all output).
- Tidy up.
- Gather and clean tools.
- Gather and organize unused parts and fasteners.
Plan for week of 4/15
- Mark at Mitaka 4/15, Kamioka 4/16-18, f2f 4/19.
- Fabian at Kamioka 4/15-18, f2f 4/19.
Vacation/Travel Info
- Mark at Mitaka 4/15.
- f2f 4/19 (Friday), 4/20, 4/21.
- Terrence's next visit from 4/18.
- Fabian's vacation 4/26 to 5/10.
- Mark's vacation from about 5/22 to 6/11.
- Mark's final day 6/28.