|
Size: 4142
Comment:
|
Size: 2929
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 5: | Line 5: |
| * Type B Past Week Summary * Mark, Fabian and Hirata-san cleaned glue off the dummy BS, attached Akutsu-san's new SS mirror plates, reglued the flags and prisms, and removed the gluing hardware, so the dummy BS is ready for shipping. Tatsumi-san's refinements to the tooling (especially the new flag holders) worked very smoothly. We were more generous with the glue and much more careful with the alignment of the prisms to the barrel, both during rehearsal and the final gluing. * Mark wrote up the gluing procedure as a new document [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=5505| E1605505]]. (The original plan was to do an addendum to Tatsumi-san's PR gluing procedure JGW-E1504248, but there was too much material.) * Hirata-san organized with Takahashi-san to get the BS payload masses shipped to Kamioka. They will go in an air-ride truck on Wed 8/17 together with a load of Type A stuff, and will arrive early on Thu 8/17. * The RM, IM and IRM were weighed, and wrapped/packed for shipment to Kamioka. * Mark made a checklist of all the parts of the BS mirror box and gluing jig, to help with collecting the parts from Kashiwa. * Mark, Fabian and Hirata-san retrieved the dummy BS and mirror box from Kashiwa. * Fabian designed an extra 600 g of trim masses for the IM and Hirata-san made drawings and ordered them. The design allows for the masses to be added to the IM even after it has been placed in the assembly frame and the dummy optic and RM have been hung, so it should not delay work. * Mark worked on the schedule, making the next few weeks more realistic and incorporating the new plan for the SR RMs (the test will be used for SR2 but two more will be made from scratch next financial year). * Fabian worked on the payload assembly procedure. * Hirata-san washed 7 OSEMs for Akutsu-san, and various other parts for Yamamoto-san of ICRR. * Hirata-san removed the remaining glue from the BS primary and secondary prisms, as well as the prisms removed from the PR hanging test mirror. (The small sapphire prisms for the PR were not intended to be reused and one had already broken at Kashiwa, but the metal PR secondaries can and will be used again.) * Type B ongoing issues * OSEMs * Akutsu-san is working to get wide-mouth OSEMs ([[http://klog.icrr.u-tokyo.ac.jp/osl/?r=1853|2 assembled]]; another few were assembled and a batch of 7 were washed. * Longer cables for BF->PI and SF->PI. * Connectors RECEIVED, cables being made. * Lower breadboard stuff * Installation to be incorporated into the procedure document. Mark/Takahashi to discuss. * Documents * BS Assembly Procedure [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=4235| E1504235]], [[https://onedrive.live.com/redir?resid=D5CCFA70A378E0D0!195&authkey=!AM_usynuo9QI57g&ithint=folder,webloc|E1504235 draft]] * To-do list during Mark's vacation * Weigh IM/RM/IRM (Fabian, Hirata) - DONE * New trim mass - ORDERED. * Pack/ship IM/RM/IRM to Kamioka (Hirata/Fabian) - READY TO SHIP. * Analyze geophone data (Fabian/Shoda) - DONE. * Remove glue from dummy BS face (Fabian) - MOSTLY DONE. * Reglue flags and prisms (Tatsumi, Fabian) - from Friday 8/5. * Clean wire for BS and RM (Hirata) - DONE * Get new winch parts for new wire diameters - ORDERED, expected 8/5. * Do fit/function test of winches (Fabian/Hirata) - fit test DONE, function test from 8/8 * Ship winches to Kamioka (Hirata/Fabian) * Work on BS simulation (Fabian) * Do Inventor assembly for SR2 in chamber and on assembly frame (Hirata) - ONGOING. * Write more of payload assembly procedure (Fabian) - ONGOING * Write more of main assembly procedure (Mark) - ONGOING * Longer term to-do list * Do BS Simulink model (Mark, Kokeyama) * Do 2D drawings of SR2 parts (Hirata) * Redesign SRx IM wire clamps for larger prisms, remachined RMs * Order SRM/PRM parts (Hirata/Shoda) * Order SRx fasteners (Hirata) |
=== Type B (Mark) === ==== Past week report ==== * Mark finished the OL calibration/diagonalization calculation and wrote it up as klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=3835|3835]] and [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7205| T1707205-v4]]. * We glued the prisms and magnets on the SR2. * We got Miyo-kun to set up the SR2-IM pico driver and tested it and the picos that will be used in the IM. * We weighed the BF for the SR2. * Enzo put DIO cards in the IO chassis and cabled them to the coil drivers. * Enzo found more of the in-vacuum cables that will be needed for SR2. Only a few remain to be found. * Enzo and Shoda-san installed the vacuum-feedthroughs on the assembly frame and routed many of the in-air cables. * Hirata-san and Mark moved the PR/SR trolley system from SR3 to SR2, reconfigured the top of the assembly frame and checked the crossbar heights. (Everything was quite close to the drawing, but a few small adjustments up/down will be required.) * Fabian found an issue with the IM: we have two of the upper movable masses and no lower ones. Probably one of the PRs has been built with two lower masses. Unfortunately an upper mass has an extra hole in an inconvenient place and can't be used as a lower mass. Hirata-san ordered a suitable plug part from Misumi, and Fabian washed it and glued it in with EP30. * Fabian assembled the RM and test-assembled the IRM. (The IRM will have to be partly disassembled during installation.) * Shoda-san and Enzo got all the control loops working on the BS, and worked with Izumi-san to steer the beam down the Y-arm. They found the passive damping was not working very well, even after correcting a 1.5 mm height error in F0. We may need to lower the damper ring. * Shoda-san created a BS Guardian. * We got Yamamoto-san to connect up the SR2 rack and create an SR2 real-time model. ==== Plan for week of 12/18 ==== * Shoda-san vacation * Mark, Fabian, Enzo, Kozu-kun at Kamioka Mon-Wed. * Find plumb bob. * Assembly frame alignment and optical table centering. (Mark and Hirata) * Finish IM assembly and pico test. (Fabian and Enzo) * Do inventory of ballast masses. (Fabian) ==== Plan for week of 12/25 ==== * Mark, Enzo, Fabian vacation * Shoda-san, Kozu-kun, Hirata-san at Kamioka Mon-Thu. * Install IM ring interface blocks and IM ring. * Install new jack receptacles (in SR3 area, second floor) on load gauge adapter (SR2 area, second floor). (Hirata-san) * OL setup. ==== Plan for week of 1/9 ==== * Mark, Fabian, Enzo, Shoda-san at Kamioka Tue-Fri. * Hang SR and RM. ==== Vacation Info ==== * Mark 12/22-1/3 * Enzo, 12/21-12/27 (but ''not'' 12/28) * Fabian 12/22-1/5 * Hirata-san 12/21-22 (conference) * Shoda-san 12/18-21 |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Past week report
Mark finished the OL calibration/diagonalization calculation and wrote it up as klog 3835 and T1707205-v4.
- We glued the prisms and magnets on the SR2.
- We got Miyo-kun to set up the SR2-IM pico driver and tested it and the picos that will be used in the IM.
- We weighed the BF for the SR2.
- Enzo put DIO cards in the IO chassis and cabled them to the coil drivers.
- Enzo found more of the in-vacuum cables that will be needed for SR2. Only a few remain to be found.
- Enzo and Shoda-san installed the vacuum-feedthroughs on the assembly frame and routed many of the in-air cables.
- Hirata-san and Mark moved the PR/SR trolley system from SR3 to SR2, reconfigured the top of the assembly frame and checked the crossbar heights. (Everything was quite close to the drawing, but a few small adjustments up/down will be required.)
- Fabian found an issue with the IM: we have two of the upper movable masses and no lower ones. Probably one of the PRs has been built with two lower masses. Unfortunately an upper mass has an extra hole in an inconvenient place and can't be used as a lower mass. Hirata-san ordered a suitable plug part from Misumi, and Fabian washed it and glued it in with EP30.
- Fabian assembled the RM and test-assembled the IRM. (The IRM will have to be partly disassembled during installation.)
- Shoda-san and Enzo got all the control loops working on the BS, and worked with Izumi-san to steer the beam down the Y-arm. They found the passive damping was not working very well, even after correcting a 1.5 mm height error in F0. We may need to lower the damper ring.
- Shoda-san created a BS Guardian.
- We got Yamamoto-san to connect up the SR2 rack and create an SR2 real-time model.
Plan for week of 12/18
- Shoda-san vacation
- Mark, Fabian, Enzo, Kozu-kun at Kamioka Mon-Wed.
- Find plumb bob.
- Assembly frame alignment and optical table centering. (Mark and Hirata)
- Finish IM assembly and pico test. (Fabian and Enzo)
- Do inventory of ballast masses. (Fabian)
Plan for week of 12/25
- Mark, Enzo, Fabian vacation
- Shoda-san, Kozu-kun, Hirata-san at Kamioka Mon-Thu.
- Install IM ring interface blocks and IM ring.
- Install new jack receptacles (in SR3 area, second floor) on load gauge adapter (SR2 area, second floor). (Hirata-san)
- OL setup.
Plan for week of 1/9
- Mark, Fabian, Enzo, Shoda-san at Kamioka Tue-Fri.
- Hang SR and RM.
Vacation Info
- Mark 12/22-1/3
Enzo, 12/21-12/27 (but not 12/28)
- Fabian 12/22-1/5
- Hirata-san 12/21-22 (conference)
- Shoda-san 12/18-21