|
Size: 2658
Comment:
|
Size: 2522
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 5: | Line 5: |
| * Type B Past Week Summary - weeks of 8/22 and 8/29 * Fabian, Mark, Zhao-kun and Yokogawa-kun did BS installation at Kamioka: * Weighed the BF, SF and dummy BS (in mirror box). * Moved the geophones onto the optical table, clamped them down and took another time series for analysis. * Aligned the IM, installed the extra trim masses, tested the picos and weighed the whole assembly. * Placed vacuum flanges and cleaned D-Sub cables ready for routing to the rack. * Realigned and immobilized the optical table (which had been bumped). * Made safety improvements on the second floor (new safety rail, new arrangement of floor pieces, caution tape around holes) * Suspended the dummy BS. Currently however it is not hanging correctly, but is off in the +Y direction by several mm relative to the mirror box. * We set up the BS OL, using one of the wheeled chests of drawers as a base and using the OL breadboard from the PR2 assembly frame. * Hirata-san made a 3D assembly model for SR2 and added the optical design. * Hirata-san worked with Uchiyama-san to solve the 90° rotation problem. It turns out the "box" part with the pistons can be rotated, so we can build the SR2 according to the original design. * Hirata-san investigated the puzzle of the BF-IM maraging rods, where the 2D drawings and 3D CAD do not agree. Fortunately the actual parts seem to agree with the 3D CAD. * Hirata-san washed 3 OSEMs (last of initial 10 for BS) and parts for two BFs (for Type A). He moved the BF parts into the clean room and will assemble them with ATC staff from next Wednesday 9/7. * Type B ongoing issues * Longer cables for BF->PI and SF->PI - RECEIVED * Longer term to-do list * Decide position of BS rack - DONE * Do Inventor assembly for SR2 in chamber and on assembly frame (Hirata) - NEARLY DONE. * Write more of payload assembly procedure (Fabian) - ONGOING * Write more of BS Assembly Procedure [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=4235| E1504235]], [[https://onedrive.live.com/redir?resid=D5CCFA70A378E0D0!195&authkey=!AM_usynuo9QI57g&ithint=folder,webloc|E1504235 draft]] (Mark) - ONGOING * Lower breadboard installation to be incorporated into the procedure document. * Work on BS simulation (Fabian) * Do BS Simulink model (Mark, Kokeyama) * Do 2D drawings of SR2 parts (Hirata) * Redesign SRx IM wire clamps for larger prisms, remachined RMs * Order SRM/PRM parts (Hirata/Shoda) * Order SRx fasteners (Hirata) |
=== Type B (Mark) === ==== Past week report ==== At Kamioka (Mark, Fabian, Enzo, Perry, Hirata-san): |
| Line 34: | Line 9: |
| * Filed crane adapter ring to make it fit better on the hook. * Debugged the BF and SF LVDTs (the signal generator had lost its settings in the rack shutdown). * Debugged the TM-H4 OSEM problem (a "Type 3 extension cable had gone bad). * Weighed eyebolts used to lie the SF. * Shipped the old pico driver and joystick back to Mitaka for Eleonora. * Borrowed a second pico driver ("PR3") and set it and "BS" up in the rack. * Practiced driving the BF cap picos with the new drivers. * (With help from Miyo-kun) got the pico MEDM screens running. * Replace the temporary "PR3" driver with a new one "BS_BF", and renamed "BS" to "BS_IM". * Checked all the DIO connections to the LPCD and connected up the HPCDs. With help from Kokeyama-san we can now see all the drivers from EPICS. * Worked on balancing the BF/IRM/IM... section. Sometime during this work, the IM sank and would not come back to its proper position even with the fishing rod. We put a scale under the RM and found that the imbalance was 488 g. Using the fishing rod we got this down to 235 g, but we found that the direction of the stepper was not consistently related to the direction selected on the driver screen - we had previously noted that "left" was "up, but driving "up" the imbalance would decrease to 235 g and then start increasing again, indicating the stepper had bounced off some obstacle. (There was no obvious sound when this happened, unlike at the low end.) * We decided to give up on tuning the height of the IM with the fishing rod and to proceed with the test hang by locking the BF keystone at the desired height. * Hirata-san installed the PI fishing rod and magic wand, and did more work on changing the PI LVDT connectors from female to male. * Enzo made many edits to the circuit diagram, adding the DIO for the HPCDs and correcting minor mistakes. ==== Plan for coming weeks ==== For more detail, see [[KAGRA/Subgroups/VIS/TypeB/ToDo]]. Week of 4/17: * Install temporary ballast mass in SF. * Lift SF/BF/... section and check total weight and SF balance. * Continue swap of PI LVDT connectors (female->male) * Start preparing LBB spring units. Week of 4/24: * Crane in PI. * Connect SF/BF... section. * Temporarily remove PI and adjust SF ballast if necessary. |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Past week report
At Kamioka (Mark, Fabian, Enzo, Perry, Hirata-san):
- Filed crane adapter ring to make it fit better on the hook.
- Debugged the BF and SF LVDTs (the signal generator had lost its settings in the rack shutdown).
- Debugged the TM-H4 OSEM problem (a "Type 3 extension cable had gone bad).
- Weighed eyebolts used to lie the SF.
- Shipped the old pico driver and joystick back to Mitaka for Eleonora.
- Borrowed a second pico driver ("PR3") and set it and "BS" up in the rack.
- Practiced driving the BF cap picos with the new drivers.
- (With help from Miyo-kun) got the pico MEDM screens running.
- Replace the temporary "PR3" driver with a new one "BS_BF", and renamed "BS" to "BS_IM".
- Checked all the DIO connections to the LPCD and connected up the HPCDs. With help from Kokeyama-san we can now see all the drivers from EPICS.
- Worked on balancing the BF/IRM/IM... section. Sometime during this work, the IM sank and would not come back to its proper position even with the fishing rod. We put a scale under the RM and found that the imbalance was 488 g. Using the fishing rod we got this down to 235 g, but we found that the direction of the stepper was not consistently related to the direction selected on the driver screen - we had previously noted that "left" was "up, but driving "up" the imbalance would decrease to 235 g and then start increasing again, indicating the stepper had bounced off some obstacle. (There was no obvious sound when this happened, unlike at the low end.)
- We decided to give up on tuning the height of the IM with the fishing rod and to proceed with the test hang by locking the BF keystone at the desired height.
- Hirata-san installed the PI fishing rod and magic wand, and did more work on changing the PI LVDT connectors from female to male.
- Enzo made many edits to the circuit diagram, adding the DIO for the HPCDs and correcting minor mistakes.
Plan for coming weeks
For more detail, see KAGRA/Subgroups/VIS/TypeB/ToDo.
Week of 4/17:
- Install temporary ballast mass in SF.
- Lift SF/BF/... section and check total weight and SF balance.
Continue swap of PI LVDT connectors (female->male)
- Start preparing LBB spring units.
Week of 4/24:
- Crane in PI.
- Connect SF/BF... section.
- Temporarily remove PI and adjust SF ballast if necessary.