|
Size: 2449
Comment:
|
Size: 2573
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 5: | Line 5: |
| * Type B Past Week Summary, weeks of 9/19 and 9/26 * Fabian, Mark and Kuwahara-kun did BS installation at Kamioka: * The BS clean booth was modified 9/20-21 to allow crane access. The area was fairly clean when Fabian inspected it on 9/26, but there were lots of metal flakes stuck to tape holding foil over the slit in the top of the clean bag. * Mark created a new Type B rtcds model and MEDM screens for the BS, adapting the TypeBb/PR3. * Mark and Kokeyama-san debugged the new model, fixing several issues. * Kuwahara-kun derived OSEM2EUL and EUL2OSEM matrices. * Mark set up OSEMINF filters using measured OSEM calibration data to return outputs in µm. * Mark took free-swing data on the TM stage to get the pendulum mode frequencies for comparison to the SUMCON model. * Mark and Fabian debugged the coil output to the OSEMs. (At first the coil drive was not giving output because it did not have BIO inputs and so was reading the test input, not the main input. And for a while output failed because of a loose cable to the sat amp.) * Mark took fixed-sine TFs to check the polarity of the coil-magnet combinations. * Hirata-san: * Finished 3D CAD of SRM in tanks (but some work was lost due to a hard disk crash). * Did 3D and 2D for new maraging rods, stub flags for PR/SR (ditto re hard disk). * Measured/tested Type A BF #8 and started assembling #9. * Longer term to-do list * Do Inventor assembly for SRx in chamber and on assembly frame (Hirata) - SR2/SR3 DONE, SRM ongoing. * Part "disk security" top has to be modified - screw positions do not match. * Write more of payload assembly procedure (Fabian) - ONGOING * Write more of BS Assembly Procedure [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=4235| E1504235]], [[https://onedrive.live.com/redir?resid=D5CCFA70A378E0D0!195&authkey=!AM_usynuo9QI57g&ithint=folder,webloc|E1504235 draft]] (Mark) - ONGOING * Lower breadboard installation to be incorporated into the procedure document. * Work on BS simulation (Fabian) * Do BS Simulink model (Mark, Kokeyama) - TM/IM/BF level DONE * Do 2D drawings of SR2 parts (Hirata) * Redesign SRx IM wire clamps for larger prisms, remachined RMs * Order SRM/PRM parts (Hirata/Shoda) * Order SRx fasteners (Hirata) |
=== Type B (Mark) === ==== Past week report ==== At Kamioka (Mark, Fabian, Enzo, Perry, Hirata-san): |
| Line 32: | Line 9: |
| * We removed the PI from the assembly frame. * We encountered a problem with the PI-SF rod jamming in the SF. We finally got it out by clamping a pig of vice grips to the rod and hammering. We found that the receptacle part was the right size (7.0 mm) but had been deformed around the edge. Hirata-san used a knife and sandpaper to lean up the edge and then ultrasonically cleaned it. * We cleared space for the PR2 team to remove a bellows from their tank. * We installed safety bars near the assembly frame at about waist height for someone on the tall ladder. We reinforced the clamps with cable ties. * We removed the LLB blade units from the PI, removed the blades from the clamps and sent the blades away for more rework to fix the length problem. Fortunately the tab section at the tip is fairly long, so we can just add a second hole further from the end. * We removed the SF cap and stored it on crossbars within the assembly frame. * We tested the SR fishing rod again, but it would only go up, not down. We found that reseting the driver fixed it, but we also moved the driver boxes into the cleanbooth to reduce the length of the motor cables. (Instead, we had to run some long DC and LAN cables.) * We adjusted the limit nut on the SF fishing rod to increase the range. * We removed one segment of the Cu ring on the SF cap and reconfigured the rest to be symmetrical. * Fabian designed a layout for the SF damper ring magnets that would work with the modified Cu ring, and placed the magnets with the template. The poles of the magnets were not on the expected faces so we had to stand the magnets up with the , ==== Plan for coming weeks ==== For more detail, see [[KAGRA/Subgroups/VIS/TypeB/ToDo]]. Week of 5/15: * Enzo from Tuesday 5/16 (driving test), rest of team from Monday. * Fix PI-SF rod jamming. * Remove PI and SF cap. * Continue debugging SF LVDT. * Reconfigure Cu damper ring on SF. * Add magnets to upper SF damper ring. * Add cable clamps on the PI (a few places are inaccessible when the PI is on the assembly frame). * Reinstall PI, this time with rods and damper ring. * Reinstall PI-SF rod, this time with hex cable clamp. * Prepare for PR2 bellows removal on 5/15 (move table with tools). * Cable/test PI horizontal LVDTs and steppers. * Install/cable/test geophones. |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Past week report
At Kamioka (Mark, Fabian, Enzo, Perry, Hirata-san):
- We removed the PI from the assembly frame.
- We encountered a problem with the PI-SF rod jamming in the SF. We finally got it out by clamping a pig of vice grips to the rod and hammering. We found that the receptacle part was the right size (7.0 mm) but had been deformed around the edge. Hirata-san used a knife and sandpaper to lean up the edge and then ultrasonically cleaned it.
- We cleared space for the PR2 team to remove a bellows from their tank.
- We installed safety bars near the assembly frame at about waist height for someone on the tall ladder. We reinforced the clamps with cable ties.
- We removed the LLB blade units from the PI, removed the blades from the clamps and sent the blades away for more rework to fix the length problem. Fortunately the tab section at the tip is fairly long, so we can just add a second hole further from the end.
- We removed the SF cap and stored it on crossbars within the assembly frame.
- We tested the SR fishing rod again, but it would only go up, not down. We found that reseting the driver fixed it, but we also moved the driver boxes into the cleanbooth to reduce the length of the motor cables. (Instead, we had to run some long DC and LAN cables.)
- We adjusted the limit nut on the SF fishing rod to increase the range.
- We removed one segment of the Cu ring on the SF cap and reconfigured the rest to be symmetrical.
- Fabian designed a layout for the SF damper ring magnets that would work with the modified Cu ring, and placed the magnets with the template. The poles of the magnets were not on the expected faces so we had to stand the magnets up with the ,
Plan for coming weeks
For more detail, see KAGRA/Subgroups/VIS/TypeB/ToDo.
Week of 5/15:
- Enzo from Tuesday 5/16 (driving test), rest of team from Monday.
- Fix PI-SF rod jamming.
- Remove PI and SF cap.
- Continue debugging SF LVDT.
- Reconfigure Cu damper ring on SF.
- Add magnets to upper SF damper ring.
- Add cable clamps on the PI (a few places are inaccessible when the PI is on the assembly frame).
- Reinstall PI, this time with rods and damper ring.
- Reinstall PI-SF rod, this time with hex cable clamp.
- Prepare for PR2 bellows removal on 5/15 (move table with tools).
- Cable/test PI horizontal LVDTs and steppers.
- Install/cable/test geophones.