|
Size: 2709
Comment:
|
Size: 1305
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 5: | Line 5: |
| * Type B Past Week Summary, weeks of 9/19 and 9/26 * Fabian, Mark and Kuwahara-kun did BS installation at Kamioka: * The BS clean booth was modified 9/20-21 to allow crane access. The area was fairly clean when Fabian inspected it on 9/26, but there were lots of metal flakes stuck to tape holding foil over the slit in the top of the clean bag. * Mark created a new Type B rtcds model and MEDM screens for the BS, adapting the TypeBb/PR3. * Mark and Kokeyama-san debugged the new model, fixing several issues. * Kuwahara-kun derived OSEM2EUL and EUL2OSEM matrices. * Mark set up OSEMINF filters using measured OSEM calibration data to return outputs in µm. * Mark took free-swing data on the TM stage to get the pendulum mode frequencies for comparison to the SUMCON model. * Mark and Fabian debugged the coil output to the OSEMs. (At first the coil drive was not giving output because it did not have BIO inputs and so was reading the test input, not the main input. And for a while output failed because of a loose cable to the sat amp.) * Mark took fixed-sine TFs to check the polarity of the coil-magnet combinations. * Mark installed a BIO card in the PR2 rack and added cables from the TM voltage and current monitors to as-yet unused IM OSEM inputs to check the calibration. * Fabian wrapped the assembly frame in cling wrap to see if it helped with wind during TFs. * Hirata-san: * Finished 3D CAD of SRM in tanks (but some work was lost due to a hard disk crash). * Did 3D and 2D for new maraging rods, stub flags for PR/SR (ditto re hard disk). * Measured/tested Type A BF #8 and started assembling #9. * Longer term to-do list * Do Inventor assembly for SRx in chamber and on assembly frame (Hirata) - SR2/SR3 DONE, SRM ongoing. * Part "disk security" top has to be modified - screw positions do not match. * Write more of payload assembly procedure (Fabian) - ONGOING * Write more of BS Assembly Procedure [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=4235| E1504235]], [[https://onedrive.live.com/redir?resid=D5CCFA70A378E0D0!195&authkey=!AM_usynuo9QI57g&ithint=folder,webloc|E1504235 draft]] (Mark) - ONGOING * Lower breadboard installation to be incorporated into the procedure document. * Work on BS simulation (Fabian) * Do BS Simulink model (Mark, Kokeyama) - TM/IM/BF level DONE * Do 2D drawings of SR2 parts (Hirata) * Redesign SRx IM wire clamps for larger prisms, remachined RMs * Order SRM/PRM parts (Hirata/Shoda) * Order SRx fasteners (Hirata) |
=== Type B (Mark) === ==== Past week report ==== At Kamioka (Mark, Fabian, Enzo, Hirata-san): * With help from Kokeyama-san and Miyakawa-san, we debugged a problem with the real-time model freezing, which turned out to be the IO chassis shutting down because of brownout condition from an overloaded AC circuit. A combination of extra boxes added to the rack, plus surge current from the air shower could draw the full 20 A limit of the circuit. Awai-san ran a cable to a separate circuit and we moved the IO chassis onto that. * We got the stepper motor cabling and driver working, and tested the BF fishing rod stepper motor. * We got the LVDT cabling, driver and associated parts of the real-time model working. * We found all the parts for the SF and the SF section of the security structure, and prepared the SF. However we then removed the Cu ring from the top cap for recleaning. * ==== Plan for coming weeks ==== Next week: * Everyone (Mark, Fabian, Enzo, Hirata-san) at Kamioka, Monday-Thursday. * Work on electronics, possibly suspend and weigh BF. Week after next: * Everyone (Mark, Fabian, Enzo, Hirata-san) at Kamioka, Monday-Friday. * Add SF and suspend BF. |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Past week report
At Kamioka (Mark, Fabian, Enzo, Hirata-san):
- With help from Kokeyama-san and Miyakawa-san, we debugged a problem with the real-time model freezing, which turned out to be the IO chassis shutting down because of brownout condition from an overloaded AC circuit. A combination of extra boxes added to the rack, plus surge current from the air shower could draw the full 20 A limit of the circuit. Awai-san ran a cable to a separate circuit and we moved the IO chassis onto that.
- We got the stepper motor cabling and driver working, and tested the BF fishing rod stepper motor.
- We got the LVDT cabling, driver and associated parts of the real-time model working.
- We found all the parts for the SF and the SF section of the security structure, and prepared the SF. However we then removed the Cu ring from the top cap for recleaning.
Plan for coming weeks
Next week:
- Everyone (Mark, Fabian, Enzo, Hirata-san) at Kamioka, Monday-Thursday.
- Work on electronics, possibly suspend and weigh BF.
Week after next:
- Everyone (Mark, Fabian, Enzo, Hirata-san) at Kamioka, Monday-Friday.
- Add SF and suspend BF.