|
Size: 2709
Comment:
|
Size: 3274
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 5: | Line 5: |
| * Type B Past Week Summary, weeks of 9/19 and 9/26 * Fabian, Mark and Kuwahara-kun did BS installation at Kamioka: * The BS clean booth was modified 9/20-21 to allow crane access. The area was fairly clean when Fabian inspected it on 9/26, but there were lots of metal flakes stuck to tape holding foil over the slit in the top of the clean bag. * Mark created a new Type B rtcds model and MEDM screens for the BS, adapting the TypeBb/PR3. * Mark and Kokeyama-san debugged the new model, fixing several issues. * Kuwahara-kun derived OSEM2EUL and EUL2OSEM matrices. * Mark set up OSEMINF filters using measured OSEM calibration data to return outputs in µm. * Mark took free-swing data on the TM stage to get the pendulum mode frequencies for comparison to the SUMCON model. * Mark and Fabian debugged the coil output to the OSEMs. (At first the coil drive was not giving output because it did not have BIO inputs and so was reading the test input, not the main input. And for a while output failed because of a loose cable to the sat amp.) * Mark took fixed-sine TFs to check the polarity of the coil-magnet combinations. * Mark installed a BIO card in the PR2 rack and added cables from the TM voltage and current monitors to as-yet unused IM OSEM inputs to check the calibration. * Fabian wrapped the assembly frame in cling wrap to see if it helped with wind during TFs. * Hirata-san: * Finished 3D CAD of SRM in tanks (but some work was lost due to a hard disk crash). * Did 3D and 2D for new maraging rods, stub flags for PR/SR (ditto re hard disk). * Measured/tested Type A BF #8 and started assembling #9. * Longer term to-do list * Do Inventor assembly for SRx in chamber and on assembly frame (Hirata) - SR2/SR3 DONE, SRM ongoing. * Part "disk security" top has to be modified - screw positions do not match. * Write more of payload assembly procedure (Fabian) - ONGOING * Write more of BS Assembly Procedure [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=4235| E1504235]], [[https://onedrive.live.com/redir?resid=D5CCFA70A378E0D0!195&authkey=!AM_usynuo9QI57g&ithint=folder,webloc|E1504235 draft]] (Mark) - ONGOING * Lower breadboard installation to be incorporated into the procedure document. * Work on BS simulation (Fabian) * Do BS Simulink model (Mark, Kokeyama) - TM/IM/BF level DONE * Do 2D drawings of SR2 parts (Hirata) * Redesign SRx IM wire clamps for larger prisms, remachined RMs * Order SRM/PRM parts (Hirata/Shoda) * Order SRx fasteners (Hirata) |
=== Type B (Mark) === ==== Past week report ==== At Kamioka (Enzo): * Enzo (with help from Miyo-kun) fixed the broken actuation coil on PI LVDT #0. * Enzo worked on the final cabling plan for BS and SRx. * Enzo replaced the LVDT driver again to have one with no dead channels (and free up the partly non-working cards for servicing). |
| Line 34: | Line 12: |
| At Mitaka and Kashiwa (Mark, Hirata-san, Fabian, Enzo): * We glued magnets into their holders. * We did a walk-through of the gluing procedure at Mitaka and discovered that the secondary prisms were missing. * We took the mirror box and gluing tools to Kashiwa to do as much of the gluing as possible. * Hirose-san applied First Contact to the BS and he and Kieran moved it into the mirror box. * We practiced putting sapphire prisms on the BS but didn't apply glue. * We tried the magnet gluing jigs designed by Aso-san and found two major issues: the overall length was about 25 mm too long, and there was no adjustment to allow for the wedge. * We designed a simple modification to the jigs that hopefully would be trivial for the ATC to do: the jigs will be cut in half and the bottom section will be mounted with adhesive on an 11 mm rod that slides in the central hole of the top section. Thus the top half can be screwed into the existing recess, and the bottom half with the magnets and glue can be allowed to drop about 3 mm onto the face of the optic. Hirata-san worked with ATC to get this done and it should be ready today (Friday 7/7). * Hirata-san also got ATC to make some jigs to hold the old 5-mm prisms so that they can be ground down to 3 mm to replace the missing ones. Hirata-san will do the grinding himself today (Friday 7/7/). * We decided to continue the gluing work at Kamioka, so we brought the BS back to Mitaka and will ship it on to Kamioka next Tuesday. * Hirata-san did a version of the 3D CAD with the as-built BS Test Hang configuration. ==== Plan for weeks of 7/10, 7/17 ==== Mark, Enzo mostly at Kamioka. * More TFs. * Receive BS at Kamioka, do gluing if possible. * Document LVDT driver rebuild and other changes. * Learn how Miyo-kun's pico driver software works and make fixes/improvements. * Design/install matrices, blend filters and damping filters. * Finish tidying rack and labeling cables. * Add temporary ballast to LBB and find total required. * Try rearranging arc weights to make room for magic wand. * Start on creating SR3 rack. * Preparation for BF rebuild. |
|
| Line 35: | Line 37: |
| Fabian, Hirata-san at Mitaka. * Clean BS secondary prisms and modified gluing jigs (Hirata-san). * Ship gluing tools and BS to Kamioka. * Do new 3D CAD for final BS install (Hirata-san): * On-assembly-frame version. * In-tank version. * Design SR assembly frame (Fabian). * Do 2D Drawings and procurement of final IM/BF/SF ballast masses (Hirata-san). * Other purchasing and preparation (spare BS clamps, suspension wire, 8-mm rod receptacles) * Do mass budget for LBB - design ballast masses (Fabian) Vacation Info: Hirata-san: Thu 7/20 through Mon 7/24 Enzo: Sat 7/22 through Sun 8/6 Fabian: Fri 8/4 through Mon 8/21 Mark: TBD Mid-Oct |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Past week report
At Kamioka (Enzo):
- Enzo (with help from Miyo-kun) fixed the broken actuation coil on PI LVDT #0.
- Enzo worked on the final cabling plan for BS and SRx.
- Enzo replaced the LVDT driver again to have one with no dead channels (and free up the partly non-working cards for servicing).
At Mitaka and Kashiwa (Mark, Hirata-san, Fabian, Enzo):
- We glued magnets into their holders.
- We did a walk-through of the gluing procedure at Mitaka and discovered that the secondary prisms were missing.
- We took the mirror box and gluing tools to Kashiwa to do as much of the gluing as possible.
- Hirose-san applied First Contact to the BS and he and Kieran moved it into the mirror box.
- We practiced putting sapphire prisms on the BS but didn't apply glue.
- We tried the magnet gluing jigs designed by Aso-san and found two major issues: the overall length was about 25 mm too long, and there was no adjustment to allow for the wedge.
- We designed a simple modification to the jigs that hopefully would be trivial for the ATC to do: the jigs will be cut in half and the bottom section will be mounted with adhesive on an 11 mm rod that slides in the central hole of the top section. Thus the top half can be screwed into the existing recess, and the bottom half with the magnets and glue can be allowed to drop about 3 mm onto the face of the optic. Hirata-san worked with ATC to get this done and it should be ready today (Friday 7/7).
- Hirata-san also got ATC to make some jigs to hold the old 5-mm prisms so that they can be ground down to 3 mm to replace the missing ones. Hirata-san will do the grinding himself today (Friday 7/7/).
- We decided to continue the gluing work at Kamioka, so we brought the BS back to Mitaka and will ship it on to Kamioka next Tuesday.
- Hirata-san did a version of the 3D CAD with the as-built BS Test Hang configuration.
Plan for weeks of 7/10, 7/17
Mark, Enzo mostly at Kamioka.
- More TFs.
- Receive BS at Kamioka, do gluing if possible.
- Document LVDT driver rebuild and other changes.
- Learn how Miyo-kun's pico driver software works and make fixes/improvements.
- Design/install matrices, blend filters and damping filters.
- Finish tidying rack and labeling cables.
- Add temporary ballast to LBB and find total required.
- Try rearranging arc weights to make room for magic wand.
- Start on creating SR3 rack.
- Preparation for BF rebuild.
Fabian, Hirata-san at Mitaka.
- Clean BS secondary prisms and modified gluing jigs (Hirata-san).
- Ship gluing tools and BS to Kamioka.
- Do new 3D CAD for final BS install (Hirata-san):
- On-assembly-frame version.
- In-tank version.
- Design SR assembly frame (Fabian).
- Do 2D Drawings and procurement of final IM/BF/SF ballast masses (Hirata-san).
- Other purchasing and preparation (spare BS clamps, suspension wire, 8-mm rod receptacles)
- Do mass budget for LBB - design ballast masses (Fabian)
Vacation Info: Hirata-san: Thu 7/20 through Mon 7/24 Enzo: Sat 7/22 through Sun 8/6 Fabian: Fri 8/4 through Mon 8/21 Mark: TBD Mid-Oct