|
Size: 2136
Comment:
|
Size: 1344
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 5: | Line 5: |
| * Type B Past Week Summary, weeks of 9/19 and 9/26 * Fabian, Mark and Liu-kun did BS installation at Kamioka: * Connected the DIO card to the LPCD. (Simulink model changes will be needed to make use of it.) * Took TF data from the TM-H1 coil output to the voltage and current monitors and found that the response was approximately flat. * Used the 90° prism and the optical lever to set the pitch of the RM to match the dummy BS. * Removed the RM trolley and added the bottom section of the security structure. * Lifted the IM/RM/BS with the load gauge adapter and load gauge and measured its mass. * Hirata-san: * Modified drawing of maraging rods for BS [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=5706| D1605706]] * Made 3D models of stub flag gluing jigs. * Made 3D models and 2D drawing of BS BF-IM hexagon cable clamp assembly and cone parts. [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=5734| D1605734]] * Washed parts and screws. * (For Type A) Assembled and adjusted blades of BF #9. * Longer term to-do list * Do Inventor assembly for SRx in chamber and on assembly frame (Hirata) - SR2/SR3 DONE, SRM ongoing. * Part "disk security" top has to be modified - screw positions do not match. * Write more of payload assembly procedure (Fabian) - ONGOING * Write more of BS Assembly Procedure [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=4235| E1504235]], [[https://onedrive.live.com/redir?resid=D5CCFA70A378E0D0!195&authkey=!AM_usynuo9QI57g&ithint=folder,webloc|E1504235 draft]] (Mark) - ONGOING * Lower breadboard installation to be incorporated into the procedure document. * Work on BS simulation (Fabian) * Do BS Simulink model (Mark, Kokeyama) - TM/IM/BF level DONE * Do 2D drawings of SR2 parts (Hirata) * Redesign SRx IM wire clamps for larger prisms, remachined RMs * Order SRM/PRM parts (Hirata/Shoda) * Order SRx fasteners (Hirata) |
* Hirata-san: * Made BS disposable wire clamp 3Dmodel and drawings. * Made ballast mass drawings for BS Bottomfilter and Standardfilter. * Made parts list and screw list for disposable wire clamp and ballast mass. * Sent drawings and lists to i-ject for quotation. * Start to make drawings for SR big parts (optical bench,damper rings,sus wires,cable clamps) - ongoing. * Mark, Fabian and Enzo (at Kamioka): * Realized that some of the imbalance in the BF was from the fishing rod and calculated a new set of blade offsets to center the rod but leave the torque from the FR to be cancelled by the trim mass for now. * Applied the blade offsets and checked that the BF hung as expected. * Found that the yoke was rubbing again and corrected it by putting it at an angle matching the keystone. * Found that the cables were adding too much stiffness and friction and rerouted them. * Found that the GAS was unstable and reduced the compression symmetrically to get 0.37 Hz. * Rebalanced the IM to set the right pitch, yaw and height. * Tested the IM picos. Unfortunately the pitch pico stuck near or at one end of its range and we will need to take the end plate off the IM to find out what is wrong. |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
- Hirata-san:
- Made BS disposable wire clamp 3Dmodel and drawings.
- Made ballast mass drawings for BS Bottomfilter and Standardfilter.
- Made parts list and screw list for disposable wire clamp and ballast mass.
- Sent drawings and lists to i-ject for quotation.
- Start to make drawings for SR big parts (optical bench,damper rings,sus wires,cable clamps) - ongoing.
- Mark, Fabian and Enzo (at Kamioka):
- Realized that some of the imbalance in the BF was from the fishing rod and calculated a new set of blade offsets to center the rod but leave the torque from the FR to be cancelled by the trim mass for now.
- Applied the blade offsets and checked that the BF hung as expected.
- Found that the yoke was rubbing again and corrected it by putting it at an angle matching the keystone.
- Found that the cables were adding too much stiffness and friction and rerouted them.
- Found that the GAS was unstable and reduced the compression symmetrically to get 0.37 Hz.
- Rebalanced the IM to set the right pitch, yaw and height.
- Tested the IM picos. Unfortunately the pitch pico stuck near or at one end of its range and we will need to take the end plate off the IM to find out what is wrong.