|
Size: 2312
Comment:
|
Size: 2409
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 5: | Line 5: |
| * Type B Past Week Summary * Fabian, Mark and Liu-kun did BS installation at Kamioka: * They replaced the thrust bearing in the BF with a stainless version. While replacing the picomotor spring, they found several issues with screws. * They removed the sheet metal cable clamp on the bottom of the BF and installed a redesigned one. * They installed the "flying saucer" cable clamp on the maraging rod between the IM and BF, and attached the cables. There was an issue with the cables from the bottom OSEMs, which are too short by about 300 mm. * They suspended the IM. Relative to the mass budget, about 700 g of trim mass had to be taken off to get good balance. There was also a problem with rubbing. It turned out that the keystone and the attached central PEEK coil former for the LVDT were at an angle, and the inside of the coil former was fouling on the outside of the pole piece for the magnets. It's not yet clear why the keystone was misaligned. * Hirata-san: * Made drawings of (revised) stub flag gluing jigs. * Worked on BS full-assembly drawings for Saito-sensei. * (For other groups) * Made a 3D model of maraging wires. * Finished making drawings of PRM inner frame. * Worked on re-setting up PC after crash. * Longer term to-do list * Do Inventor assembly for SRx in chamber and on assembly frame (Hirata) - SR2/SR3 DONE, SRM ongoing. * Part "disk security" top has to be modified - screw positions do not match. * Write more of payload assembly procedure (Fabian) - ONGOING * Write more of BS Assembly Procedure [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=4235| E1504235]], [[https://onedrive.live.com/redir?resid=D5CCFA70A378E0D0!195&authkey=!AM_usynuo9QI57g&ithint=folder,webloc|E1504235 draft]] (Mark) - ONGOING * Lower breadboard installation to be incorporated into the procedure document. * Work on BS simulation (Fabian) * Do BS Simulink model (Mark, Kokeyama) - TM/IM/BF level DONE * Do 2D drawings of SR2 parts (Hirata) * Redesign SRx IM wire clamps for larger prisms, remachined RMs * Order SRM/PRM parts (Hirata/Shoda) * Order SRx fasteners (Hirata) |
* Mark and Fabian debugged the rubbing issue with the BS. It turns out the EQ stops between the IRM and IM are so misaligned that they can't be used at all. This misalignment was noted on 10/27 klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=2090|2090]] but seems to have gotten worse. With the stops removed, the OSEMs (adjusted on 10/27) are still fairly well centered, so the problem probably predates the earthquake of 11/1. * The IMM/IRM stops were removed, and Fabian installed the brackets that have EQ stop screws for the IRM. (Thus both the IM and IRM can be restrained independently, but not relatively.) * Mark worked on the PR2 rack: * Rearranged the items in the rack to make space for new AA and AI chassis at the bottom near the IO chassis. * Replaced the AA chassis, which had had a group of channels marked as bad by Michimura-san. * Installed a second AA chassis and a second AI chassis in the rack. * Installed a second ADC card and a second DAC card in the IO chassis. * Modified the k1ioppr2 real-time model to recognize the new ADC/DAC cards and also the extra DIO cards installed previously. * Attempted to modify the k1visbs real-time model to recognize the new ADC/DAC cards. Unfortunately, apparently due to changes to library parts made by Okutomi-san, neither the original model or Okutomi-san's new model can be successfully compiled and installed anymore! Debugging is ongoing. * Mark and Fabian did a stocktake of all the unused in-vacuum cables. There should be enough for the BS test hang. * Fabian finished the redesign of the EQ stops for the BS RM. Hirata-san will refine the 3D design and do drawings. * Fabian redesigned the cable clamp on top of the multi-purpose cube (on the BS RM) to avoid the need for clips. (These are too easily moved when the cables are moved during installation and removal of the safety bar between the RM and IM, which has to be done many times.) He will do a similar one for SR. * Mark and Fabian reviewed the previous IJECT payload parts order and flagged the items that need updating. * Mark worked on task lists and schedule, but the server still won't allow logins to upload anything. * Hirata-san finished the PR/SR mirror box modifications. * Hirata-san washed parts (screws and collets). |
| Line 31: | Line 22: |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Mark and Fabian debugged the rubbing issue with the BS. It turns out the EQ stops between the IRM and IM are so misaligned that they can't be used at all. This misalignment was noted on 10/27 klog 2090 but seems to have gotten worse. With the stops removed, the OSEMs (adjusted on 10/27) are still fairly well centered, so the problem probably predates the earthquake of 11/1.
- The IMM/IRM stops were removed, and Fabian installed the brackets that have EQ stop screws for the IRM. (Thus both the IM and IRM can be restrained independently, but not relatively.)
- Mark worked on the PR2 rack:
- Rearranged the items in the rack to make space for new AA and AI chassis at the bottom near the IO chassis.
- Replaced the AA chassis, which had had a group of channels marked as bad by Michimura-san.
- Installed a second AA chassis and a second AI chassis in the rack.
- Installed a second ADC card and a second DAC card in the IO chassis.
- Modified the k1ioppr2 real-time model to recognize the new ADC/DAC cards and also the extra DIO cards installed previously.
- Attempted to modify the k1visbs real-time model to recognize the new ADC/DAC cards. Unfortunately, apparently due to changes to library parts made by Okutomi-san, neither the original model or Okutomi-san's new model can be successfully compiled and installed anymore! Debugging is ongoing.
- Mark and Fabian did a stocktake of all the unused in-vacuum cables. There should be enough for the BS test hang.
- Fabian finished the redesign of the EQ stops for the BS RM. Hirata-san will refine the 3D design and do drawings.
- Fabian redesigned the cable clamp on top of the multi-purpose cube (on the BS RM) to avoid the need for clips. (These are too easily moved when the cables are moved during installation and removal of the safety bar between the RM and IM, which has to be done many times.) He will do a similar one for SR.
- Mark and Fabian reviewed the previous IJECT payload parts order and flagged the items that need updating.
- Mark worked on task lists and schedule, but the server still won't allow logins to upload anything.
- Hirata-san finished the PR/SR mirror box modifications.
- Hirata-san washed parts (screws and collets).