|
Size: 2232
Comment:
|
Size: 1963
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 5: | Line 5: |
| * Type B Past Week Summary * Fabian, Mark and Liu-kun did BS installation at Kamioka: * Replaced the thrust bearing in the BF with a stainless version. While replacing the picomotor spring, they found several issues with screws. * Removed the sheet metal cable clamp on the bottom of the BF and installed a redesigned one. * They installed the "flying saucer" cable clamp on the maraging rod between the IM and BF, and attached the cables. There was an issue with the cables from the bottom OSEMs, which are too short by about 300 mm. * Ruspended the IM. Relative to the mass budget, about 700 g of trim mass had to be taken off to get good balance. There was also a problem with rubbing. It turned out that the keystone and the attached central PEEK coil former for the LVDT were at an angle, and the inside of the coil former was fouling on the outside of the pole piece for the magnets. It's not yet clear why the keystone was misaligned. * Hirata-san: * Made drawings of (revised) stub flag gluing jigs. * Worked on BS full-assembly drawings for Saito-sensei. * (For other groups) * Made a 3D model of maraging wires. * Finished making drawings of PRM inner frame. * Worked on re-setting up PC after crash. * Longer term to-do list * Do Inventor assembly for SRx in chamber and on assembly frame (Hirata) - SR2/SR3 DONE, SRM ongoing. * Part "disk security" top has to be modified - screw positions do not match. * Write more of payload assembly procedure (Fabian) - ONGOING * Write more of BS Assembly Procedure [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=4235| E1504235]], [[https://onedrive.live.com/redir?resid=D5CCFA70A378E0D0!195&authkey=!AM_usynuo9QI57g&ithint=folder,webloc|E1504235 draft]] (Mark) - ONGOING * Lower breadboard installation to be incorporated into the procedure document. * Work on BS simulation (Fabian) * Do 2D drawings of SR2 parts (Hirata) * Redesign SRx IM wire clamps for larger prisms, remachined RMs * Order SRM/PRM parts (Hirata/Shoda) * Order SRx fasteners (Hirata) |
=== Type B (Mark) === ==== Past week report ==== At Kamioka (Mark, Ohishi-san, Fabian, Enzo, Hirata-san, Yoshioka-kun, Kozu-kun): * We put lock nuts on the F0 FR and calibrated the F0 LVDT against FR position and keystone height. * Enzo traced the issue with the geophones to a specific cable. * We measured the BF and F0 GAS resonant frequencies. * We adjusted the spacing of the SR damper. * We double-checked the BS pitch with the OL. * We debugged the PI yaw mechanism. We managed to get the return spring properly adjusted, but the stepper motor tends to jam because of the strange design. * '''We prepared the suspension for lifting and craned it into the tank.''' * Hirata-san fixed an issue with one of the nailheads on the LBB intermediate ring support rods not properly seating, by removing the rod and reinstalling it upside down (with the problem nailhead in a less critical position). * Enzo and team moved all the in-air cables from the assembly frame to the tank. * Fabian and Ohishi-san unlocked the bottom section of the suspension and got it hanging freely. ==== Plan for week of 9/25 ==== Mark, Fabian, Enzo (Mon, Tue), Ohishi-san (Tue, Fri), Hirata-san, Yoshioka-kun (Tue, Wed, Fri), Kozu-kun * Finish moving in-air cabling and feedthroughs and reconnect in-vacuum cables (through Cu O-rings). * Unlock rest of suspension and readjust. * Debug electronics. * Unclamp LBB ring "sandwich" so LBB Cu ring is suspended on upper rods. * Install LBB lower rods and hook LBB. * Adjust LBB damper Cu-magnet gap. * Measure required ballast for LBB. * Remove First Contact, try OL. * Prepare for SR2 work. |
| Line 30: | Line 31: |
| ==== Plan for week of 10/2 ==== Kamioka: Mark, Enzo, Fabian, Ohishi-san. * TFs etc. Mitaka: Hirata-san? * SF design/purchasing. ==== Vacation Info ==== Mark: 10/16-24 Enzo: 9/27-29 |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Past week report
At Kamioka (Mark, Ohishi-san, Fabian, Enzo, Hirata-san, Yoshioka-kun, Kozu-kun):
- We put lock nuts on the F0 FR and calibrated the F0 LVDT against FR position and keystone height.
- Enzo traced the issue with the geophones to a specific cable.
- We measured the BF and F0 GAS resonant frequencies.
- We adjusted the spacing of the SR damper.
- We double-checked the BS pitch with the OL.
- We debugged the PI yaw mechanism. We managed to get the return spring properly adjusted, but the stepper motor tends to jam because of the strange design.
We prepared the suspension for lifting and craned it into the tank.
- Hirata-san fixed an issue with one of the nailheads on the LBB intermediate ring support rods not properly seating, by removing the rod and reinstalling it upside down (with the problem nailhead in a less critical position).
- Enzo and team moved all the in-air cables from the assembly frame to the tank.
- Fabian and Ohishi-san unlocked the bottom section of the suspension and got it hanging freely.
Plan for week of 9/25
Mark, Fabian, Enzo (Mon, Tue), Ohishi-san (Tue, Fri), Hirata-san, Yoshioka-kun (Tue, Wed, Fri), Kozu-kun
- Finish moving in-air cabling and feedthroughs and reconnect in-vacuum cables (through Cu O-rings).
- Unlock rest of suspension and readjust.
- Debug electronics.
- Unclamp LBB ring "sandwich" so LBB Cu ring is suspended on upper rods.
- Install LBB lower rods and hook LBB.
- Adjust LBB damper Cu-magnet gap.
- Measure required ballast for LBB.
- Remove First Contact, try OL.
- Prepare for SR2 work.
Plan for week of 10/2
Kamioka: Mark, Enzo, Fabian, Ohishi-san.
- TFs etc.
Mitaka: Hirata-san?
- SF design/purchasing.
Vacation Info
Mark: 10/16-24 Enzo: 9/27-29