|
Size: 1249
Comment:
|
Size: 2841
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 5: | Line 5: |
| * Type B Past Week Summary * Mark and Hirata-san worked at Kamioka, with valuable help from Enzo (on loan from Type Bp team). * We got all the adapter cables for the BF made (Hirata-san did some work on Monday at Mitaka). * We installed the extension for the BF yaw pico on the IM pico adapter cable. * We got all the in-vacuum and in-air cabling for the IM OSEMs done. * We tried to install the stepper and LVDT adapter cables but realized we didn't have enough information on which wires was which. (We later tracked this info down but did not have time to do anything with it - we would have needed to do the rest of the in-vacuum and in-air cabling and set up the stepper motor and LVDT drivers, so we concentrated on the OSEMs.) * We plugged in the IM OSEMs, set gains and offsets, and did a noise test (analysis and klog pending). * We mounted the OSEMs on the IRM and routed the cabling neatly. * We released the suspension. * We adjusted the OSEM mounting plates to center the OSEMs on the flags. * We adjusted the OSEMs in/out to midrange. * The suspension is now ready for OSEM-OSEM TFs! |
=== Type B (Mark) === ==== Report for week of 5/7 ==== * We inspected the wires and clamps involved in the wire break. * The scars on the clamp on the tungsten wire that failed had very different depths, with the one that failed being much deeper, so probably the clamp piece was not completely straight before tensioning. However one wire on the other side was also badly crushed and on the point of failing, so the tension was clearly too much. * We decided on new torque specs of 2 N.m for the primary clamps (down from 5 N.m) and 10 N.m (down from 20 N.m) for the secondary. The secondary clamp spec, for M6 screws, is now based on the LIGO policy of using the maximum suggested for the screw and the LIGO value for a coated 1/4-20 screw (100 in-lb = 11.3 N.m), and the primary clamp spec is derated by 2/3 from the spec for an M5 screw because the clamp pieces are recessed and only grip the wire at narrow sections along the edges, concentrating the force. * None of the screws showed any signs of damage. * All of the scars on the primary clamps were shallow enough that could reuse the clamp pieces. The tungsten secondary clamps were never tightened, and the outer pieces of piano wire secondary clamps were badly scarred but could be reused upside down. * We successfully rehung the SR3 and RM. In the process we noticed and fixed an issue with the assembly frame (due to an out-of-date number in the Mirapro diagram, the IM crossbars were set 3 mm too high, which would have affected the wire length). * We added the sections of the security structure below the RM and up to the BF. * We installed the TM OSEM cables and routed them up to the IM. * We installed the load gauge adapter and load gauge and prepared the IM/... section for weighing. * We removed the three cracked F0 blades from the PI #3 in the SRM, and prepared for testing prototype new blades in that PI. We removed a floor panel under the PI and set up the filter service trolley underneath it with a stack of masses for a dummy load. ==== Plan for week of 5/14 ==== * Mark, Enzo, Hirata-san, Kozu-kun at Kamioka Mon-Thu, then Osaka. * ==== Plan for week of 5/21 ==== * Mark, Enzo, Hirata-san, Kamioka Mon-Fri. * Kozu-kun at Kamioka Wed-Fri. ==== Plan for week of 5/28 ==== * Mark, Enzo, Hirata-san, Kamioka Mon-Fri. * Kozu-kun at Kamioka Mon only. ==== To-Do Lists, Schedule ==== * [[KAGRA/Subgroups/VIS/TypeB/March2018]] * [[KAGRA/Subgroups/VIS/TypeB/April2018]] * [[KAGRA/Subgroups/VIS/TypeB/ToDoBS]] * [[KAGRA/Subgroups/VIS/TypeB/ToDoSR]] * [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7779|JGW-L1807779-v1 Type B Schedule (SR)]] ==== Vacation Info ==== |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Report for week of 5/7
- We inspected the wires and clamps involved in the wire break.
- The scars on the clamp on the tungsten wire that failed had very different depths, with the one that failed being much deeper, so probably the clamp piece was not completely straight before tensioning. However one wire on the other side was also badly crushed and on the point of failing, so the tension was clearly too much.
- We decided on new torque specs of 2 N.m for the primary clamps (down from 5 N.m) and 10 N.m (down from 20 N.m) for the secondary. The secondary clamp spec, for M6 screws, is now based on the LIGO policy of using the maximum suggested for the screw and the LIGO value for a coated 1/4-20 screw (100 in-lb = 11.3 N.m), and the primary clamp spec is derated by 2/3 from the spec for an M5 screw because the clamp pieces are recessed and only grip the wire at narrow sections along the edges, concentrating the force.
- None of the screws showed any signs of damage.
- All of the scars on the primary clamps were shallow enough that could reuse the clamp pieces. The tungsten secondary clamps were never tightened, and the outer pieces of piano wire secondary clamps were badly scarred but could be reused upside down.
- We successfully rehung the SR3 and RM. In the process we noticed and fixed an issue with the assembly frame (due to an out-of-date number in the Mirapro diagram, the IM crossbars were set 3 mm too high, which would have affected the wire length).
- We added the sections of the security structure below the RM and up to the BF.
- We installed the TM OSEM cables and routed them up to the IM.
- We installed the load gauge adapter and load gauge and prepared the IM/... section for weighing.
- We removed the three cracked F0 blades from the PI #3 in the SRM, and prepared for testing prototype new blades in that PI. We removed a floor panel under the PI and set up the filter service trolley underneath it with a stack of masses for a dummy load.
Plan for week of 5/14
- Mark, Enzo, Hirata-san, Kozu-kun at Kamioka Mon-Thu, then Osaka.
Plan for week of 5/21
- Mark, Enzo, Hirata-san, Kamioka Mon-Fri.
- Kozu-kun at Kamioka Wed-Fri.
Plan for week of 5/28
- Mark, Enzo, Hirata-san, Kamioka Mon-Fri.
- Kozu-kun at Kamioka Mon only.
To-Do Lists, Schedule