Size: 1239
Comment:
|
Size: 2079
Comment:
|
Deletions are marked like this. | Additions are marked like this. |
Line 5: | Line 5: |
* Type B Past Week Summary * Mark and Hirata-san worked at Kamioka, with valuable help from Enzo (on loan from Type Bp team). * We got all the adapter cables for the BF made (Hirata-san did some work on Monday at Mitaka). * We installed the extension for the BF yaw pico on the IM pico adapter cable. * We got all the in-vacuum and in-air cabling for the IM OSEMs done. * We tried to install the stepper and LVDT adapter cables but realized we didn't have enough information on which wires was which. (We later tracked this info down but did not have time to do anything with it - we would have needed to do the rest of the in-vacuum and in-air cabling and set up the stepper motor and LVDT drivers, so we concentrated on the OSEMs.) * We plugged in the IM OSEMs, set gains and offsets, and did a noise test (analysis and klog pending). * We mounted the OSEMs on the IRM and routed the cabling neatly. * We released the suspension. * We adjusted the OSEM mounting plates to center the OSEMs on the flags. * We adjusted the OSEMs in/out to midrange. * The suspension is now ready for OSEM-OSEM TFs! |
=== Type B (Mark) === ==== Past week report ==== At Kamioka (Mark, Enzo, Simon, Type Bp team): * Mark remade the BF pico adapter cable which was poorly made and had also been damaged. * The Type Bp team tided up the BS rack and made new labels for many cables (thanks!). * Enzo connected up the in-air cables for the picos and steppers. * Mark and Enzo renumbered the PI LVDTs, geophones and LVDTs to make a consistent scheme working anticlockwise. * Enzo and Mark debugged all the cables. The only problem we couldn't solve was that the actuator coil for PI LVDT #0 is open-circuit at the connector on the LVDT. (It has been intermittent but worked before the craning.) We may have to redo the connector or replace the LVDT. Limited TFs will be possible in the next week. * Simon set up the LSOL and was easily able to get a return beam from the mirror on the dummy BS. * Shoda-san copied over the LSOL section of the PR3 real-time model into the BS model and made other improvements (thanks!). * Mark brought home At Mitaka (Fabian, Hirata-san): * Fabian finished designing final trim masses for IM/BF/SF for the final hang of the BS and passed it to Hirata-san to make drawings and get quotes. * Hirata-san requested quotes for the replaceable-jaw version of the BS wire clamps. * Fabian and Hirata-san gathered needed items for the BS prism/flag gluing. * Hirata-san designed receptacles for the new rods with 8 mm heads and requested quotes. ==== Plan for week of 7/3 ==== * Do prism/flag gluing on real BS at Kashiwa (whole team). * Do new 3D CAD (Hirata-san): * SR2 on BS assembly frame. (Adjust jack positions if possible, or leave for Fabian/Mark to do.) * Final BS build, SS/PI/SF as for Test Hang but with BF/IRM/IM/BS/RM down rotated back to original direction. * On-assembly-frame version. (Adjust jack positions if possible, or leave for Mark to do.) * In-tank version. * ==== Plan for week of 7/10 ==== |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Past week report
At Kamioka (Mark, Enzo, Simon, Type Bp team):
- Mark remade the BF pico adapter cable which was poorly made and had also been damaged.
- The Type Bp team tided up the BS rack and made new labels for many cables (thanks!).
- Enzo connected up the in-air cables for the picos and steppers.
- Mark and Enzo renumbered the PI LVDTs, geophones and LVDTs to make a consistent scheme working anticlockwise.
- Enzo and Mark debugged all the cables. The only problem we couldn't solve was that the actuator coil for PI LVDT #0 is open-circuit at the connector on the LVDT. (It has been intermittent but worked before the craning.) We may have to redo the connector or replace the LVDT. Limited TFs will be possible in the next week.
- Simon set up the LSOL and was easily able to get a return beam from the mirror on the dummy BS.
- Shoda-san copied over the LSOL section of the PR3 real-time model into the BS model and made other improvements (thanks!).
- Mark brought home
At Mitaka (Fabian, Hirata-san):
- Fabian finished designing final trim masses for IM/BF/SF for the final hang of the BS and passed it to Hirata-san to make drawings and get quotes.
- Hirata-san requested quotes for the replaceable-jaw version of the BS wire clamps.
- Fabian and Hirata-san gathered needed items for the BS prism/flag gluing.
- Hirata-san designed receptacles for the new rods with 8 mm heads and requested quotes.
Plan for week of 7/3
- Do prism/flag gluing on real BS at Kashiwa (whole team).
- Do new 3D CAD (Hirata-san):
- SR2 on BS assembly frame. (Adjust jack positions if possible, or leave for Fabian/Mark to do.)
- Final BS build, SS/PI/SF as for Test Hang but with BF/IRM/IM/BS/RM down rotated back to original direction.
- On-assembly-frame version. (Adjust jack positions if possible, or leave for Mark to do.)
- In-tank version.