|
Size: 1887
Comment:
|
Size: 3274
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 5: | Line 5: |
| * Type B Past Week Summary * Mark (with Enzo) did initial TFs on the BF. * Did fixed-sine TFs on individual OSEMs at low frequency to check actuator polarity (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=2176 | 2176]] and [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=2182|2182]]). * Set gains in the COILOUTF block to compensate for actuator polarity. * Mark (with Enzo) did a free-swing measurement on the BS after earthquake of 11/22 (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=2182|2182]]). * Results suspicious (noted by Shoda-san): too much difference between OSEMs - horizontal showing much less motion than vertical. * Possible rubbing in horizontal. * May need a trip to Kamioka. * Mark (with Enzo) made corrections and improvements to many of the MEDM screens (klog [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=2176 | 2176]] and [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=2182|2182]]). * Main overview screen was not generic in many places, and links to GDS_TP screens were broken. * ADC monitor screen referenced bad channels with LIGO-style names. * DAC monitor screen was not generic and did not support IM OSEMs. * Watchdog IM OSEM AC band limit filter screen was a copy of the TM one. * Watchdog TM OSEM AC band limit filter screen appears to be getting OL signals as input - needs model changes to fix. * The zoomed screens for IM OSEM centering were called incorrectly and did not work. * Various screens had LIGO-style channel names as labels. * Mark did a draft of D1603600-v12 reflecting the new assignment of IM OSEMs to DAQ channels (#4-9 are now V1, V2, V3, H1, H2, H3 rather than H1, H2, ...) from last Friday (the wiring was changed to reflect the model). * Mark worked on schedule. * Hirata-san |
=== Type B (Mark) === ==== Past week report ==== At Kamioka (Enzo): * Enzo (with help from Miyo-kun) fixed the broken actuation coil on PI LVDT #0. * Enzo worked on the final cabling plan for BS and SRx. * Enzo replaced the LVDT driver again to have one with no dead channels (and free up the partly non-working cards for servicing). At Mitaka and Kashiwa (Mark, Hirata-san, Fabian, Enzo): * We glued magnets into their holders. * We did a walk-through of the gluing procedure at Mitaka and discovered that the secondary prisms were missing. * We took the mirror box and gluing tools to Kashiwa to do as much of the gluing as possible. * Hirose-san applied First Contact to the BS and he and Kieran moved it into the mirror box. * We practiced putting sapphire prisms on the BS but didn't apply glue. * We tried the magnet gluing jigs designed by Aso-san and found two major issues: the overall length was about 25 mm too long, and there was no adjustment to allow for the wedge. * We designed a simple modification to the jigs that hopefully would be trivial for the ATC to do: the jigs will be cut in half and the bottom section will be mounted with adhesive on an 11 mm rod that slides in the central hole of the top section. Thus the top half can be screwed into the existing recess, and the bottom half with the magnets and glue can be allowed to drop about 3 mm onto the face of the optic. Hirata-san worked with ATC to get this done and it should be ready today (Friday 7/7). * Hirata-san also got ATC to make some jigs to hold the old 5-mm prisms so that they can be ground down to 3 mm to replace the missing ones. Hirata-san will do the grinding himself today (Friday 7/7/). * We decided to continue the gluing work at Kamioka, so we brought the BS back to Mitaka and will ship it on to Kamioka next Tuesday. * Hirata-san did a version of the 3D CAD with the as-built BS Test Hang configuration. ==== Plan for weeks of 7/10, 7/17 ==== Mark, Enzo mostly at Kamioka. * More TFs. * Receive BS at Kamioka, do gluing if possible. * Document LVDT driver rebuild and other changes. * Learn how Miyo-kun's pico driver software works and make fixes/improvements. * Design/install matrices, blend filters and damping filters. * Finish tidying rack and labeling cables. * Add temporary ballast to LBB and find total required. * Try rearranging arc weights to make room for magic wand. * Start on creating SR3 rack. * Preparation for BF rebuild. Fabian, Hirata-san at Mitaka. * Clean BS secondary prisms and modified gluing jigs (Hirata-san). * Ship gluing tools and BS to Kamioka. * Do new 3D CAD for final BS install (Hirata-san): * On-assembly-frame version. * In-tank version. * Design SR assembly frame (Fabian). * Do 2D Drawings and procurement of final IM/BF/SF ballast masses (Hirata-san). * Other purchasing and preparation (spare BS clamps, suspension wire, 8-mm rod receptacles) * Do mass budget for LBB - design ballast masses (Fabian) Vacation Info: Hirata-san: Thu 7/20 through Mon 7/24 Enzo: Sat 7/22 through Sun 8/6 Fabian: Fri 8/4 through Mon 8/21 Mark: TBD Mid-Oct |
Scraps of text for incorporation in the VIS Meeting Minutes
KAGRA/Subgroups/VIS/MeetingNAOJ
Type B (Mark)
Past week report
At Kamioka (Enzo):
- Enzo (with help from Miyo-kun) fixed the broken actuation coil on PI LVDT #0.
- Enzo worked on the final cabling plan for BS and SRx.
- Enzo replaced the LVDT driver again to have one with no dead channels (and free up the partly non-working cards for servicing).
At Mitaka and Kashiwa (Mark, Hirata-san, Fabian, Enzo):
- We glued magnets into their holders.
- We did a walk-through of the gluing procedure at Mitaka and discovered that the secondary prisms were missing.
- We took the mirror box and gluing tools to Kashiwa to do as much of the gluing as possible.
- Hirose-san applied First Contact to the BS and he and Kieran moved it into the mirror box.
- We practiced putting sapphire prisms on the BS but didn't apply glue.
- We tried the magnet gluing jigs designed by Aso-san and found two major issues: the overall length was about 25 mm too long, and there was no adjustment to allow for the wedge.
- We designed a simple modification to the jigs that hopefully would be trivial for the ATC to do: the jigs will be cut in half and the bottom section will be mounted with adhesive on an 11 mm rod that slides in the central hole of the top section. Thus the top half can be screwed into the existing recess, and the bottom half with the magnets and glue can be allowed to drop about 3 mm onto the face of the optic. Hirata-san worked with ATC to get this done and it should be ready today (Friday 7/7).
- Hirata-san also got ATC to make some jigs to hold the old 5-mm prisms so that they can be ground down to 3 mm to replace the missing ones. Hirata-san will do the grinding himself today (Friday 7/7/).
- We decided to continue the gluing work at Kamioka, so we brought the BS back to Mitaka and will ship it on to Kamioka next Tuesday.
- Hirata-san did a version of the 3D CAD with the as-built BS Test Hang configuration.
Plan for weeks of 7/10, 7/17
Mark, Enzo mostly at Kamioka.
- More TFs.
- Receive BS at Kamioka, do gluing if possible.
- Document LVDT driver rebuild and other changes.
- Learn how Miyo-kun's pico driver software works and make fixes/improvements.
- Design/install matrices, blend filters and damping filters.
- Finish tidying rack and labeling cables.
- Add temporary ballast to LBB and find total required.
- Try rearranging arc weights to make room for magic wand.
- Start on creating SR3 rack.
- Preparation for BF rebuild.
Fabian, Hirata-san at Mitaka.
- Clean BS secondary prisms and modified gluing jigs (Hirata-san).
- Ship gluing tools and BS to Kamioka.
- Do new 3D CAD for final BS install (Hirata-san):
- On-assembly-frame version.
- In-tank version.
- Design SR assembly frame (Fabian).
- Do 2D Drawings and procurement of final IM/BF/SF ballast masses (Hirata-san).
- Other purchasing and preparation (spare BS clamps, suspension wire, 8-mm rod receptacles)
- Do mass budget for LBB - design ballast masses (Fabian)
Vacation Info: Hirata-san: Thu 7/20 through Mon 7/24 Enzo: Sat 7/22 through Sun 8/6 Fabian: Fri 8/4 through Mon 8/21 Mark: TBD Mid-Oct