Size: 2102
Comment:
|
Size: 3395
Comment:
|
Deletions are marked like this. | Additions are marked like this. |
Line 10: | Line 10: |
* --(Typical OSEM sensitivity measured when locking the target.)-- | * Produce a nicer figure. (Fabian.) * --(Typical OSEM sensitivity measured when locking the target. These are Panwei's measurements.)-- |
Line 32: | Line 33: |
* Produce a nicer plot. (Fabian.) | |
Line 37: | Line 39: |
What we have | === Control topology === Copy and modify whatever Terrence wrote already. (Fabian.) |
Line 39: | Line 42: |
What we aim for | === Performance at low frequencies === * Magnetic damper ring. Include Rikako and Enzo’s measurements. (Fabian andEnzo.) * Temperature stability. (Fabian.) * Measured quality factors of resonances with control system on and off. (To be mesured by Fabian after the 1st wave of the pendemic.) * Damping time of resonant motion with the control system on and off. (To be mesured by Fabian after the 1st wave of the pandemic.) * Optic residual displacement and velocity rms measured with the oplev in a day with good weather; show coherence with seismometer on ground. (Fabian) * Describe the control system used: * –Say that due to time constrains and to unidentified noise sources it wasn’tpossible to implement inertial damping. * –IP: LVDT position control and damping. * –F0: LVDT position control and damping. * –F1: LVDT position control and damping. * –BF: LVDT position control and damping. * –IM OSEMs: position control from oplev and damping from the OSEMsreadout. * –Oplev: position control acting on IM and damping o the mirror. |
Describe KAGRA/Subgroups/VIS/TypeB/PaperTODOlist here.
Introduction
The mechanical system
Sensors and actuators for control
Introductory paragraph.
OSEMs
Brief description of the anatomy of the OSEMs.
- Produce a nicer figure. (Fabian.)
Typical OSEM sensitivity measured when locking the target. These are Panwei's measurements.
Typical measuring range according to all the units used in BS, SR2, SR3 and SRM.
- Typical calibration value. (Fabian, klog 4189.)
- Produce a nicer plot (Fabian).
- Write the figure caption (Fabian).
- Write a couple of sentences about the coil-magnet actuator and cite Mark’s document and Michimura-san’s paper. (Mark.)
LVDTs
Optical lever
Brief description of the oplev.
Brief description of diagonalization procedure.
Where the displacement calibration comes from: relativeposition of components measured with ruler, dimensions given by the 3D-CAD, QPD displacement calibration and comparison with IP displacement.
Typical extent of coupling after diagonalization.
Typical measuring range.
- Write the diameter of the beam determines the linear range of the QPD as a beam displacement sensor. (Fabian.)
- Point out that the oplev is expected to be limited by the seismic motion. (Fabian.)
- Say it is not easy to measure directly the oplev sensitivity but it is possible to set an upper limit to the optic rms displacement and velocities. (Fabian.)
Inertial sensors
Brief description of what a geophone is.
Brief explanation of the calculation of the noise determining the sensitivity.
- Say that below the resonant frequency the noise goes as f^-{3.5} and explain the reason. (Fabian.)
- Produce a nicer plot. (Fabian.)
Briefly say how they were calibrated against a calibrated seismometer.
Say the noise was measured using three channel correlation analysis.
Say we are in the process of finding out the reson of discrepancy betwwen the predicted and measured sensitivity.
Control and performance
Control topology
Copy and modify whatever Terrence wrote already. (Fabian.)
Performance at low frequencies
- Magnetic damper ring. Include Rikako and Enzo’s measurements. (Fabian andEnzo.)
- Temperature stability. (Fabian.)
- Measured quality factors of resonances with control system on and off. (To be mesured by Fabian after the 1st wave of the pendemic.)
- Damping time of resonant motion with the control system on and off. (To be mesured by Fabian after the 1st wave of the pandemic.)
- Optic residual displacement and velocity rms measured with the oplev in a day with good weather; show coherence with seismometer on ground. (Fabian)
- Describe the control system used:
- –Say that due to time constrains and to unidentified noise sources it wasn’tpossible to implement inertial damping.
- –IP: LVDT position control and damping.
- –F0: LVDT position control and damping.
- –F1: LVDT position control and damping.
- –BF: LVDT position control and damping.
- –IM OSEMs: position control from oplev and damping from the OSEMsreadout.
- –Oplev: position control acting on IM and damping o the mirror.