7032
Comment:
|
6362
|
Deletions are marked like this. | Additions are marked like this. |
Line 9: | Line 9: |
== Paper == * --(Review Type Bp paper)-- * --(Choose paper title)-- -> "Vibration isolation systems for the beam splitter and signal recycling mirrors of the KAGRA gravitational wave detector"? * --(Create JGWDoc number for paper)-- -> [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9836|P1909836]] * --(Decide paper author list)-- -> KAGRA Author List 2019? * Write Type B paper abstract * Write paper outline * Write Type B paper Section 1 Introduction * Vibration isolation systems in KAGRA * Write Section 2.1 Overview * Steal or reproduce Type Bp Figure 1 (optic layout) * Steal or reproduce Type Bp paper Figure 2 (suspension comparison) * Write Section 2.2 Requirements for Type B * Write Section 3 Design of the Type-B suspension * Write Section 3.1 Mechanical * Choose photo of Type B suspension in mid-air * Make diagram of Type B in vacuum chamber * Write Section 3.2 Sensors and Actuators * Write Section 3.3 Control and Damping * Make controls diagram like Type Bp paper Figure 7 * Write Section 4 Measured performance * Write Section 4.1 Damping Time * Make decay time plot like Type Bp paper Figure 8 * Write Section 4.2 Residual Velocity * Write Section 4.3 Residual Angular Fluctuations * Write Section 4.4 Vibration Isolation Performance * Write Section 5 Summary * Write Section 6 Acknowledgments * Write References Section |
|
Line 23: | Line 54: |
* Wipe inside tanks with Vectra-Alpha wipes and ethanol. | ==== All ==== * --(Debug stepper remote enable.)-- * --(Do survey of numbering of coil drivers and corresponding Contec assignments.)-- |
Line 27: | Line 61: |
* Check focus of BS camera. * Debug stepper remote enable. |
* Offload large IM/IRM yaw to IP or F0 yaw. |
Line 31: | Line 64: |
* Install GAS filter control loops. * Debug stepper remote enable. * Get rid of SR2 cable reel (shutdown FE and rack, replug everything into new power strip, start up rack and FE). * Split model. |
* --(Install GAS filter control loops.)-- |
Line 37: | Line 67: |
* Debug stepper remote enable. * Split model. |
|
Line 41: | Line 69: |
* --(Debug geophone channels!!!)-- | |
Line 43: | Line 72: |
* Debug stepper remote enable. * Check BIO connections for possible swap of GAS/IP. |
* --(Check BIO connections for possible swap of GAS/IP.)-- |
Line 46: | Line 74: |
=== Real-Time Model === |
=== Real-Time Model/Guardian === |
Line 49: | Line 76: |
* Restart k1vissrmt (Wednesday during maintenance??): * Re-convert filter files. * Stop SRM Guardian (just stop it dead - don't transition to SAFE; don't let it meddle at all). -Done for SRM and SR3 * Make fresh safe.snap. * Note all TEST and OPTICALIGN offsets. * Put large ramp times (≈30++ s) in all DAMP, TEST and OPTICALIGN filters. * Turn off all DAMP, TEST, and OPTICALIGN filter offsets and master switch. * Restart k1vissrmt. If there are gross problems, consider restarting the whole FE. * Restore safe.snap. * Debug OVERVIEW, IP and WD screens (check for white channels etc). * Restore OPTICALIGN offsets (if necessary), transfer TEST offsets to new ALIGN filters and set long ramp times. * Set new WD thresholds for IP LVDT and ACC. * Enable all DAMP, ALIGN, and OPTICALIGN offsets. * Make sure SRM Guardian is pointing to generic Type B Guardian. * Adjust Type B Guardian code to set long ramp times on all DAMP, ALIGN and OPTICALIGN filters. Wrap the ALIGN stuff in an if block for now to not break BS/SR2/SR3. * Reenable Guardian if/when satisfied. * Rebuild and restart k1visbst and initialize/test as for SRM. * --(Create new k1vissr2t, k1vissr2p, k1vissr3t, k1vissr3p based on k1vissrmt and k1vissrmp. Be sure to update DCUID numbers: * SR2 FECT=54, FECP=55 -Done * SR3 FECT=56, FECP=57)-- * (SRM FECT=58, FECP=59) * Update DCUID numbers also in /opt/rtcds/userapps/release/vis/common/medm/vissr2_overview_macro.txt and vissr3_overview_macro.txt. * Rebuild, restart k1vissr2t, k1vissr2p, k1vissr3t, k1vissr3p and initialize/test as for SRM/BS. * For SR2, just before restarting with the new real-time models, power the whole front end down and replug everything into the new power strip. * Turn off all DC-powered boxes. * Shut down the FE computer using the web server at [[http://10.68.99.171]]. * Turn off the IO chassis using the switch on the front. * Turn off the DC power supplies. * Replug all AC-powered stuff (DC supplies, IO chassis, signal generator, routers) into the new power strip that is already there. * Restore everything in reverse order. * Reset the signal generator: 10 kHz, 5 Vpp, sine wave, ON. === Guardian === * --(Make all Guardians point to TYPEB.py.)-- * --(Create a BURT `.req` file to backup the ALIGN settings for IP and GAS.)-- * --(Create a BURT `.req` file to back up the OPTICALIGN settings for the payload.)-- * --(Add UI to the MEDM screens to run BURT with either the ALIGN and OPTICALIGN `.req` files and generate `.snap` files with suitable names.)-- * Make sure the SAFE state turns off all ALIGN and OPTICALIGN offsets with long ramp times. * Have the transition from the SAFE state to the DAMPED state load the ALIGN offsets with long ramp times. * Have the transition from the DAMPED state to the ALIGNED state load the OPTICALIGN offsets with long ramp times 9and also enable damping). |
* --(Work out what IM1 and IM2 items of BIO section are actually driving based on the rack survey.)-- * --(Correct all user-facing text on BIO MEDM screen (e.g., "SRM IM-H MONITORS LPCD #1 = Contec #1L") to reflect reality.)-- * --(Rename all IM1 and IM2 items in RTM to IMH and IMV per above.)-- * --(Do a new BIO screen that points to new IMH and IMV channels (use search and replace in GEDIT), but keep the old version for the time being.)-- * --(Finalize models.)-- * * Make a new Type B Guardian and edit it to drive all the new model features and ignore the removed bits. * --(-ALIGN blocks)-- * --(-OPTICALIGN blocks.)-- * --(+SET blocks.)-- * --(+DCCTRL blocks)-- * --(Have the transition from the SAFE state to the DAMPED state load the ALIGN offsets with long ramp times.)-- * --(Have the transition from the DAMPED state to the ALIGNED state load the OPTICALIGN offsets with long ramp times and also enable damping).)-- |
VIS Type B To-Do List
Archived items are at ../ToDoOld.
Paper
Review Type Bp paper
Choose paper title -> "Vibration isolation systems for the beam splitter and signal recycling mirrors of the KAGRA gravitational wave detector"?
Create JGWDoc number for paper -> P1909836
Decide paper author list -> KAGRA Author List 2019?
- Write Type B paper abstract
- Write paper outline
- Write Type B paper Section 1 Introduction
- Vibration isolation systems in KAGRA
- Write Section 2.1 Overview
- Steal or reproduce Type Bp Figure 1 (optic layout)
- Steal or reproduce Type Bp paper Figure 2 (suspension comparison)
- Write Section 2.1 Overview
- Write Section 2.2 Requirements for Type B
- Write Section 3 Design of the Type-B suspension
- Write Section 3.1 Mechanical
- Choose photo of Type B suspension in mid-air
- Make diagram of Type B in vacuum chamber
- Write Section 3.2 Sensors and Actuators
- Write Section 3.3 Control and Damping
- Make controls diagram like Type Bp paper Figure 7
- Write Section 3.1 Mechanical
- Write Section 4 Measured performance
- Write Section 4.1 Damping Time
- Make decay time plot like Type Bp paper Figure 8
- Write Section 4.2 Residual Velocity
- Write Section 4.3 Residual Angular Fluctuations
- Write Section 4.4 Vibration Isolation Performance
- Write Section 4.1 Damping Time
- Write Section 5 Summary
- Write Section 6 Acknowledgments
- Write References Section
Every Week
Facilities
- Vacuum and roll floor.
- Wipe ladders.
- Tidy tools, parts.
Get stuff from ../WishList
2019-02-12
- Monday is public holiday.
Etc
All
Debug stepper remote enable.
Do survey of numbering of coil drivers and corresponding Contec assignments.
Choose optimum BIO Config board switch settings for all OLs. See D1302081 for what each switch does. Four of them are gain stages (24 dB, 12 dB, 6 dB, 3 dB), and three are filters (all 1 Hz zero, 10 Hz pole). Please clarify the switch numbering and functions (switch "1" = circuit board B0 = group 1, filter A1; position 1 = enable?), make a cheat sheet and put a copy in each rack.
BS
- Offload large IM/IRM yaw to IP or F0 yaw.
SR2
Install GAS filter control loops.
SR3
SRM
Debug geophone channels!!!
- Debug OL, especially whitening filter. Note that WF S1808108 has a mysterious note on its JGWDoc page suggesting it may have a fault.
- Set up LEN OL (if/when 3D QPD stage arrives).
Check BIO connections for possible swap of GAS/IP.
Real-Time Model/Guardian
Work out what IM1 and IM2 items of BIO section are actually driving based on the rack survey.
Correct all user-facing text on BIO MEDM screen (e.g., "SRM IM-H MONITORS LPCD #1 = Contec #1L") to reflect reality.
Rename all IM1 and IM2 items in RTM to IMH and IMV per above.
Do a new BIO screen that points to new IMH and IMV channels (use search and replace in GEDIT), but keep the old version for the time being.
Finalize models.
- Make a new Type B Guardian and edit it to drive all the new model features and ignore the removed bits.
-ALIGN blocks
-OPTICALIGN blocks.
+SET blocks.
+DCCTRL blocks
Have the transition from the SAFE state to the DAMPED state load the ALIGN offsets with long ramp times.
Have the transition from the DAMPED state to the ALIGNED state load the OPTICALIGN offsets with long ramp times and also enable damping).
Documentation and Operation Manual
- Add useful info from Enzo's notebook to BSData.
Minor Tasks
Mechanical
- Put pointy-tipped screw in RM trolley for BS
Electrical
- Update BS Circuit diagram, D1503600
Note removal of LED/PD on TM OSEMs.
- Organize stepper reset system and watchdog BIO.
- Include information on assignment of channels to feedthrough positions.
- Reflect gender-changers and non-flipping feedthrough adapters.
- Reflect actual cable lengths.
- Include LVDT pin size (1 mm).
- Include Stepper pin size (1.6 mm).
Undo renumbering of IP items.
Page 10: "DIO Card # 0" should be "DIO Card # 1"
Include OutConfigBoards on OL page (Sheet 18).
Update HPCD section to reflect:
All three GAS channels are on HPCD #1 and DIO Card #2, CNB cables, Sheet 13.
Three IP channels are on HPCD #0 and DIO Card #2, CNA cables, Sheet 15.
Real-time and SUMCON models
- Create SUMCON models for full BS and major installation milestones.
Create controls design description (cf LIGO-T1100378).
- Make table of ADC/DAC assignments and check for consistency with D1503600 and k1visbs (Enzo, Mark)
- Understand/document/debug Kokeyama-san's DIO stuff.
- Measure LPCD and HPCD output filter response.
- Design and install software compensation filters for LPCD and HPCD output filters.
One Day, If Ever Needed
BS
- Tune BS LBB (adjust table height, damper height) - DON'T BOTHER (unless there's an excuse to open the lower half of the tank).
- Replace BS F0 thrust bearing and yaw adjuster - BIG JOB, DON'T BOTHER (unless lack of yaw adjustment becomes a major problem).
- (Continue to) soak the sapphire prisms off the dummy BS for reuse on the SRM metal mass.
SR3
- Replace chipped magnets (12x12x12 mm) in SR3 IP, H1 and H2.
SRM
- Install Enomoto-kun's beam target plate (if/when available).
- Find two geophone cables used by Okutomi-san. (I looked in the second floor EXV room but didn't find them - Mark.)
- Find one geophone cable ordered for SRM but missing.
- Rearrange miswired geophone cable.
- Rebuild defective geophone cable.
- Put FC on SRM-W and install it in its holder with 1.4 mm shims ready for possible use.