5262
Comment:
|
7732
|
Deletions are marked like this. | Additions are marked like this. |
Line 39: | Line 39: |
* Find Type A reference * Find cryogenic payload reference * Find bKAGRA reference * Find LIGO-India reference * Find NS-NS detection reference * Find initial detection reference |
|
Line 42: | Line 47: |
=== Facilities === | |
Line 50: | Line 54: |
== 2019-04-08 == === Etc === * Health checks of suspensions before pump down. * Tidy up. * Move charging station to more convenient location (e.g., near -X entrance). * Find and inventory all gluing tools. * MEDM * Fix DAC screen (split model issue). * Real-time and SUMCON models * Add temperature alarms. * Add secondary watchdog with lower threshold that puts all outputs to HOLD and then gets Guardian to ramp them down. * SDF * Document SDF in KOM * Make SDF states for Type B * SAFE * DCCTRL-ONLY * ALIGNED-IN-AIR * ALIGNED-IN-VACUUM |
|
Line 51: | Line 73: |
=== 2019-03-04 === ==== Etc ==== * Help Fujii-kun with PRx. |
=== BS === === SR2 === * Measure decay time, rms with and without control. * Do FEA model of IRM side plates. |
Line 55: | Line 78: |
==== All ==== * Test stepper remote enable system. * Choose optimum BIO Config board switch settings for all OLs. See [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=2081| D1302081]] for what each switch does. Four of them are gain stages (24 dB, 12 dB, 6 dB, 3 dB), and three are filters (all 1 Hz zero, 10 Hz pole). Please clarify the switch numbering and functions (switch "1" = circuit board B0 = group 1, filter A1; position 1 = enable?), make a cheat sheet and put a copy in each rack. |
=== SR3 === * Put SR3 cleanbooth electronics in minirack. * Check pico adapter cables. |
Line 59: | Line 82: |
==== BS ==== * Offload large IM/IRM yaw to IP or F0 yaw. ==== SR2 ==== * Redo control filters for new topology. * Damping time measurements. ==== SR3 ==== |
=== SRM === * Check pico adapter cables. * Debug 240 Hz noise in LVDT. * Check keystone lock screws in BF (on next vent). |
Line 67: | Line 87: |
==== SRM ==== * Debug OL, especially whitening filter. Note that WF S1808108 has a mysterious note on its JGWDoc page suggesting it may have a fault. * Set up LEN OL (if/when 3D QPD stage arrives). |
== Simulation == * --(Get a good set of TFs and put them in a common directory:)-- * --(Directory: /kagra/Dropbox/Subsystems/VIS/TypeBData/SR2/simulation/TF/ )-- * --(Content: diaggui xml files and regular text files.)-- * --(Compare the Matlab prediction with the measurements.)-- * --(In a reasonable way tune the parameters of the simulation in ordet to get a good agreement.)-- * --(It should include resonant peaks not predicted by the simulation.)-- * --(Write a klog about this. )-- * --(Given the fact that Takanori's Matlab simulation provides the TFs in units of [m/N] calculate a calibration factor for each GAS LVDT and IP and IM virtual actuator, which are in units of [µm/cnt]. )-- * Collect the measurements of LVDT and OSEM readout noise and put them in a common directory: * Location: /kagra/Dropbox/Subsystems/VIS/TypeBData/SR2/simulation/sensor_readout_noise/ * Content: duaggui xml files and regular text files. * Check Panwei's measurements of OSEM noise. Pay special attention to the conversion into m/rtHz from V/rtHz. * Calculate the readut noise of the virtual sensors from the readout noise of the real ones. * --(IP LVDT.)-- * IP Geo: where's the data for SR2 geophones? There's information in entry [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=6106|6106]]. For SRM the plots are at [[http://klog.icrr.u-tokyo.ac.jp/osl/?r=8177|8177]] but where's the data? * GAS LVDT (no virtual sensors) * IM OSEMS * Oplev * Estimate coil driver noise. It seems this is not expected to contribute significantly but we should still know. * Convert real actuation noise to virtual actuation noise. * --(Check whether the Matlab simulation implements the output of the length sensing oplev)--. * Extract the filters designed by Enzo, Terrence and Lucia from the filter bank using Foton and write them in a format compatible with Takanori's simulation (which uses his own function to define the filters). * In the software modify the control feeback loop topology in order to have the same as in the real system. * Tune the filters in order to account for the differences between simulation and measurement. * As sanity check for the simulation, check the stability criteria and compare with Enzo's. * Ask whether there is a recent measurement of seismic motion at the the central room. |
Line 71: | Line 115: |
=== Real-Time Model/Guardian === * See [[KAGRA/Subgroups/VIS/OpsManual/Simulink]] * Test Guardians. === Documentation and Operation Manual === * Add useful info from Enzo's notebook to BSData. === Minor Tasks === ==== Mechanical ==== |
== Minor Tasks == === Mechanical === |
Line 84: | Line 121: |
== Electrical == | == Electronics == * Pick better restore values for sat amps. * Install Tanaka-san's LVDT sig gen cards (when available). * Test stepper remote enable system. |
Line 87: | Line 127: |
* Organize stepper reset system and watchdog BIO. | * Add stepper remote enable system. * Include watchdog. |
Line 90: | Line 131: |
* Add default and as-built stepper channel assignments. | |
Line 101: | Line 143: |
* Create SUMCON models for full BS and major installation milestones. | * Add temperature alarms. * Add secondary watchdog with lower threshold that puts all outputs to HOLD and then gets Guardian to ramp them down. * Change cycle time of SR models to match BS (2K payload and 16K top). |
Line 103: | Line 147: |
* Make table of ADC/DAC assignments and check for consistency with D1503600 and k1visbs (Enzo, Mark) | * Make table of ADC/DAC assignments and check for consistency with D1503600. |
Line 108: | Line 152: |
== Guardian == == Documentation and Operation Manual == * Add useful info from Enzo's notebook to BSData/etc. == OLs == * Design/procure/install permanent hard protective boxes. |
|
Line 109: | Line 160: |
==== BS ==== | === BS === |
Line 112: | Line 163: |
* (Continue to) soak the sapphire prisms off the dummy BS for reuse on the SRM metal mass. ==== SR3 ==== |
=== SR3 === |
Line 115: | Line 166: |
==== SRM ==== | === SRM === |
Line 117: | Line 169: |
* Find two geophone cables used by Okutomi-san. (I looked in the second floor EXV room but didn't find them - Mark.) * Find one geophone cable ordered for SRM but missing. * Rearrange miswired geophone cable. * Rebuild defective geophone cable. |
VIS Type B To-Do List
Archived items are at ../ToDoOld.
Paper
Review Type Bp paper
Choose paper title -> "Vibration isolation systems for the beam splitter and signal recycling mirrors of the KAGRA gravitational wave detector"?
Create JGWDoc number for paper -> P1909836
Decide paper author list -> KAGRA Author List 2019?
- Write Type B paper abstract
- Write paper outline
- Write Type B paper Section 1 Introduction
- Vibration isolation systems in KAGRA
- Write Section 2.1 Overview
- Steal or reproduce Type Bp Figure 1 (optic layout)
- Steal or reproduce Type Bp paper Figure 2 (suspension comparison)
- Write Section 2.1 Overview
- Write Section 2.2 Requirements for Type B
- Write Section 3 Design of the Type-B suspension
- Write Section 3.1 Mechanical
- Choose photo of Type B suspension in mid-air
- Make diagram of Type B in vacuum chamber
- Write Section 3.2 Sensors and Actuators
- Write Section 3.3 Control and Damping
- Make controls diagram like Type Bp paper Figure 7
- Write Section 3.1 Mechanical
- Write Section 4 Measured performance
- Write Section 4.1 Damping Time
- Make decay time plot like Type Bp paper Figure 8
- Write Section 4.2 Residual Velocity
- Write Section 4.3 Residual Angular Fluctuations
- Write Section 4.4 Vibration Isolation Performance
- Write Section 4.1 Damping Time
- Write Section 5 Summary
- Write Section 6 Acknowledgments
- Write References Section
- Find Type A reference
- Find cryogenic payload reference
- Find bKAGRA reference
- Find LIGO-India reference
- Find NS-NS detection reference
- Find initial detection reference
Every Week
- Vacuum and roll floor.
- Wipe ladders.
- Tidy tools, parts.
Get stuff from ../WishList
2019-04-08
Etc
- Health checks of suspensions before pump down.
- Tidy up.
- Move charging station to more convenient location (e.g., near -X entrance).
- Find and inventory all gluing tools.
- MEDM
- Fix DAC screen (split model issue).
- Real-time and SUMCON models
- Add temperature alarms.
- Add secondary watchdog with lower threshold that puts all outputs to HOLD and then gets Guardian to ramp them down.
- SDF
- Document SDF in KOM
- Make SDF states for Type B
- SAFE
- DCCTRL-ONLY
- ALIGNED-IN-AIR
- ALIGNED-IN-VACUUM
BS
SR2
- Measure decay time, rms with and without control.
- Do FEA model of IRM side plates.
SR3
- Put SR3 cleanbooth electronics in minirack.
- Check pico adapter cables.
SRM
- Check pico adapter cables.
- Debug 240 Hz noise in LVDT.
- Check keystone lock screws in BF (on next vent).
Simulation
Get a good set of TFs and put them in a common directory:
Directory: /kagra/Dropbox/Subsystems/VIS/TypeBData/SR2/simulation/TF/
Content: diaggui xml files and regular text files.
Compare the Matlab prediction with the measurements.
In a reasonable way tune the parameters of the simulation in ordet to get a good agreement.
It should include resonant peaks not predicted by the simulation.
Write a klog about this.
Given the fact that Takanori's Matlab simulation provides the TFs in units of [m/N] calculate a calibration factor for each GAS LVDT and IP and IM virtual actuator, which are in units of [µm/cnt].
- Collect the measurements of LVDT and OSEM readout noise and put them in a common directory:
- Location: /kagra/Dropbox/Subsystems/VIS/TypeBData/SR2/simulation/sensor_readout_noise/
- Content: duaggui xml files and regular text files.
- Check Panwei's measurements of OSEM noise. Pay special attention to the conversion into m/rtHz from V/rtHz.
- Calculate the readut noise of the virtual sensors from the readout noise of the real ones.
- Estimate coil driver noise. It seems this is not expected to contribute significantly but we should still know.
- Convert real actuation noise to virtual actuation noise.
Check whether the Matlab simulation implements the output of the length sensing oplev.
- Extract the filters designed by Enzo, Terrence and Lucia from the filter bank using Foton and write them in a format compatible with Takanori's simulation (which uses his own function to define the filters).
- In the software modify the control feeback loop topology in order to have the same as in the real system.
- Tune the filters in order to account for the differences between simulation and measurement.
- As sanity check for the simulation, check the stability criteria and compare with Enzo's.
- Ask whether there is a recent measurement of seismic motion at the the central room.
Minor Tasks
Mechanical
- Put pointy-tipped screw in RM trolley for BS
Electronics
- Pick better restore values for sat amps.
- Install Tanaka-san's LVDT sig gen cards (when available).
- Test stepper remote enable system.
- Update BS Circuit diagram, D1503600
Note removal of LED/PD on TM OSEMs.
- Add stepper remote enable system.
- Include watchdog.
- Include information on assignment of channels to feedthrough positions.
- Reflect gender-changers and non-flipping feedthrough adapters.
- Add default and as-built stepper channel assignments.
- Reflect actual cable lengths.
- Include LVDT pin size (1 mm).
- Include Stepper pin size (1.6 mm).
Undo renumbering of IP items.
Page 10: "DIO Card # 0" should be "DIO Card # 1"
Include OutConfigBoards on OL page (Sheet 18).
Update HPCD section to reflect:
All three GAS channels are on HPCD #1 and DIO Card #2, CNB cables, Sheet 13.
Three IP channels are on HPCD #0 and DIO Card #2, CNA cables, Sheet 15.
Real-time and SUMCON models
- Add temperature alarms.
- Add secondary watchdog with lower threshold that puts all outputs to HOLD and then gets Guardian to ramp them down.
- Change cycle time of SR models to match BS (2K payload and 16K top).
Create controls design description (cf LIGO-T1100378).
- Make table of ADC/DAC assignments and check for consistency with D1503600.
- Understand/document/debug Kokeyama-san's DIO stuff.
- Measure LPCD and HPCD output filter response.
- Design and install software compensation filters for LPCD and HPCD output filters.
Guardian
Documentation and Operation Manual
- Add useful info from Enzo's notebook to BSData/etc.
OLs
- Design/procure/install permanent hard protective boxes.
One Day, If Ever Needed
BS
- Tune BS LBB (adjust table height, damper height) - DON'T BOTHER (unless there's an excuse to open the lower half of the tank).
- Replace BS F0 thrust bearing and yaw adjuster - BIG JOB, DON'T BOTHER (unless lack of yaw adjustment becomes a major problem).
SR3
- Replace chipped magnets (12x12x12 mm) in SR3 IP, H1 and H2.
SRM
- Install Enomoto-kun's beam target plate (if/when available).
- Put FC on SRM-W and install it in its holder with 1.4 mm shims ready for possible use.