VIS Type B Near Term To-Do List

2017-04-03

Facilities (mostly full team)

• Clean up after floor work.
• Vacuum and roll floor.
• Wipe ladders.
• Tidy tools, parts.

PI Move

• General prep
  • Decide if air shower needs to be moved.
  • Triple-check dimensions around second-floor parking spot for PI; decide best place for pallet.
  • Check for obstacles along path around -X side of cleanbooth.
  • Find/clean Saito-sensei's PI lifting adapter and any needed fasteners.
  • Check both crane remote controls (clean and dirty) are charged.
• Prepare PI for moving.
  • Remove accelerometers and store safely.
  • Remove large weights. (How? With forklift at last minute? Where to?)
  • Remove arc weights (move some to second floor, wrap rest for storage).
  • Attach lifting plates.
  • Wrap with clingwrap, cover with spare cleanbag.
  • Remove old cabling from PI to rack.
• Prepare second floor for receiving PI.
  • Clean and clingwrap pallet.
  • Find metal plates and/or duckboards for on top of pallets.
  • Move BS cables on -Y side of tank off top of beam.
  • Find shims (about 75 mm high) to put on beam where cables were, to help support pallet.
• Clear path to remove PI with forklift.
  • Move any obstacles identified previously.
  • Shutdown BS/PR2 racks and move electrical cables.
  • Move any stored items on -Y side of portable cleanroom.
  • Move portable cleanroom towards -Y.
  • Move worktables from next to BS/PR2 racks.
• Move PI
  • Disconnect fan cables, curtain (Miyoki-san).
  • Unzip ceiling panel.
  • Crane pallet into cleanbooth.
  • Lay foil on pallet.
  • Forklift PI to -X,+Y corner of cleanbooth
  • Crane PI into clean booth.
• Cleanup
  • Zip up ceiling panel.
  • Reconnect fan cables, curtain (Miyoki-san).
  • Replace tables near BS/PR2 racks
  • Move portable cleanroom back to original spot.
  • Re-lay electrical cables.
  • Power up racks.

Continue PI Prep

• Finish reattaching repaired LVDT coil(s) and redoing connectors with correct gender.
• Install fishing rod.
• Find table, weights, etc for use with LBB blade bending jigs.
• Install LLB blades.
• Install LLB blade units in PI.

Hanging BF/IRM/IM/RM/BS (mostly Mark, Fabian, Perry)

• Reroute in-vacuum cables up to SF level; add in-vacuum extension cables if necessary.
• Test SF LVDT.
• Test SF fishing rod stepper.

Electronics (mostly Enzo, Mark)

• Make more anti-feedthrough adapters.
• Add retaining screws to cables at feedthroughs (mostly done, needs finishing).
• Work with Miyo-kun to get pico drivers added to BS rack and screens
• Update E1503600 with DIO card for HPCDs, etc, etc.
• Decide final length for BS OSEM cables (Enzo, Mark, Fabian)
• Send list of required in-vacuum cables to Takahashi-san
• Make table of ADC/DAC assignments and check for consistency with D1503600 and k1visbs (Enzo, Mark)
• Make spreadsheet on Google Docs or the like with in-vacuum cable inventory (Hirata)

Real-time and SUMCON models (mostly Perry, Mark)

• Get Perry (and Enzo) set up with SUMCON.
• Update SUMCON model of full BS.
• Do cut-down SUMCON model of just payload hanging from fixed BS.
• Compare measured TFs to cut-down model(s).
• Create a proper DAC Monitor MEDM screen.
• Improve ADC Monitor MEDM screen.