Differences between revisions 3 and 4
Revision 3 as of 2017-03-12 20:42:40
Size: 1707
Editor: MarkBarton
Comment:
Revision 4 as of 2017-03-13 08:13:34
Size: 2063
Editor: MarkBarton
Comment:
Deletions are marked like this. Additions are marked like this.
Line 5: Line 5:
== Facilities ==
 * Vacuum and roll floor (All)
 * Wipe ladders (All)
 * Tidy tools, parts (All)
== Facilities (mostly full team) ==
 * Vacuum and roll floor
 * Wipe ladders
 * Tidy tools, parts
Line 13: Line 13:
== Electronics == == Hanging BF/IRM/IM/RM/BS (mostly Mark, Fabian, Perry) ==
 * Adjust orientation of SF cap
 * Adjust orientation of SF
 * Find/attach cable clamps for SF
 * Hook SF-BF rod (with hex cable clamp).
 * Reroute in-vacuum cables up to SF level; add in-vacuum extension cables if necessary.
 * Suspend BF/IRM/IM/RM/BS; re-ballast and re-trim as necessary.
 * Install new security structure stuff for BS/RM.
Line 15: Line 22:
 * Wire up BF roll/pitch picos (Enzo)
 * Work with Miyo-kun to get pico drivers added to BS rack and screens (Enzo, Mark)
 * Grab remaining cables etc per E1605111 and update document (Enzo)
 * Update E1503600 with DIO card for HPCDs, etc, etc. (Enzo)
== Electronics (mostly Enzo, Mark) ==

* Wire up BF roll/pitch picos
 * Work with Miyo-kun to get pico drivers added to BS rack and screens
 * Grab remaining cables etc per E1605111 and update document
 * Run cables from third and fourth feedthroughs to rack

 * Update E1503600 with DIO card for HPCDs, etc, etc.
Line 20: Line 30:
 * Send list of required in-vacuum cables to Takahashi-san (Enzo, Mark)
 * Debug 900 Hz noise on BF LVDT output (Enzo, Mark)
 * Debug excess noise on TM-H3 OSEM (Enzo, Mark)
 * Send list of required in-vacuum cables to Takahashi-san
 * Debug 900 Hz noise on BF LVDT output
 * Debug excess noise on TM-H3 OSEM
Line 26: Line 36:
== PI Prep == == PI Prep (mostly Hirata-san, Mark) ==
Line 29: Line 39:
 * Find and reattach repaired LVDT coil(s) (???)  * Find and reattach repaired LVDT coil(s) (Enzo, Hirata, Mark)
 * Check length/gender of connectors against E1503600 (Enzo)
Line 31: Line 42:
== Hanging BF/IRM/IM/RM/BS ==
 * Correct orientation of SF cap (Mark, Fabian, Perry)
 * Correct orientation of SF (Mark, Fabian, Perry)
 * Find/attach cable clamps for SF (Fabian)

== Real-time and SUMCON models ==
== Real-time and SUMCON models (mostly Perry, Mark) ==

VIS Type B Near Term To-Do List

2017-03-13

Facilities (mostly full team)

  • Vacuum and roll floor
  • Wipe ladders
  • Tidy tools, parts
  • Find missing light lent to Kokeyama-san (Mark)
  • Mark/photograph/count peeling patches on the floor.
  • Mark/photograph/count pillars with bare concrete bases.

Hanging BF/IRM/IM/RM/BS (mostly Mark, Fabian, Perry)

  • Adjust orientation of SF cap
  • Adjust orientation of SF
  • Find/attach cable clamps for SF
  • Hook SF-BF rod (with hex cable clamp).
  • Reroute in-vacuum cables up to SF level; add in-vacuum extension cables if necessary.
  • Suspend BF/IRM/IM/RM/BS; re-ballast and re-trim as necessary.
  • Install new security structure stuff for BS/RM.

Electronics (mostly Enzo, Mark)

  • Wire up BF roll/pitch picos
  • Work with Miyo-kun to get pico drivers added to BS rack and screens
  • Grab remaining cables etc per E1605111 and update document
  • Run cables from third and fourth feedthroughs to rack
  • Update E1503600 with DIO card for HPCDs, etc, etc.
  • Decide final length for BS OSEM cables (Enzo, Mark, Fabian)
  • Send list of required in-vacuum cables to Takahashi-san
  • Debug 900 Hz noise on BF LVDT output
  • Debug excess noise on TM-H3 OSEM
  • Make table of ADC/DAC assignments and check for consistency with D1503600 and k1visbs (Enzo, Mark)
  • Make spreadsheet on Google Docs or the like with in-vacuum cable inventory (Hirata)

PI Prep (mostly Hirata-san, Mark)

  • Inspect PI, compare to CAD and 2D drawings (Hirata, Mark)
  • Identify missing PI parts (Hirata, Mark)
  • Find and reattach repaired LVDT coil(s) (Enzo, Hirata, Mark)
  • Check length/gender of connectors against E1503600 (Enzo)

Real-time and SUMCON models (mostly Perry, Mark)

  • Update SUMCON model of full BS (Perry?, Okutomi?, Mark?)
  • Do cut-down SUMCON model of just payload hanging from fixed BS (Perry?, Okitomi?, Mark?)
  • Compare measured TFs to cut-down model
  • Create a proper DAC Monitor MEDM screen
  • Improve ADC Monitor MEDM screen

KAGRA/Subgroups/VIS/TypeB/ToDoBS (last edited 2019-01-04 15:21:23 by MarkBarton)