1492
Comment:
|
← Revision 15 as of 2018-04-16 17:07:38 ⇥
1978
|
Deletions are marked like this. | Additions are marked like this. |
Line 2: | Line 2: |
== Parts/Screws == * Cu O-rings for geophones * As of 2018-04-15 * We have 3 x 150-mm and 4 x 80-mm ones. * We need 4 x 150-mm and 4 x 80-mm for SR * We need 3 x 150-mm and 3 x 80-mm if we service the BS geophones. * We need 1 x 150-mm and 1 x 80-mm spare. * -> ORDER 5 x 150-mm and 4 x 80-mm * Rubber pieces for geophones. * (3mm * ů77)*9 |
|
Line 5: | Line 16: |
* Multimeter (with ohmmeter and diode check function), e.g., [[https://www.monotaro.com/p/2091/7898/?gclid=Cj0KEQjwyZjKBRDu|Fluke 114]] | |
Line 7: | Line 17: |
* DSub9 Breakouts, e.g., [[https://www.amazon.com/Uxcell-Female-Adapter-Terminal-Connector/dp/B01736DOS8/ref=pd_lpo_vtph_147_bs_t_2?_encoding=UTF8&psc=1&refRID=PE9ZD7W1SW6MQ28RT8Q6|male]] and [[https://www.amazon.com/Adapter-Terminal-Connector-Signal-Module/dp/B00WW6YU5G/ref=pd_bxgy_328_img_2?_encoding=UTF8&pd_rd_i=B00WW6YU5G&pd_rd_r=ZQHEDMT34ZQ3AD86MKC7&pd_rd_w=HKAX6&pd_rd_wg=QfWsw&psc=1&refRID=ZQHEDMT34ZQ3AD86MKC7|female]]. One set for use at the rack (dirty) and one set for use in the cleanbbooth (clean). (The one we have is [[https://www.amazon.com/Terminal-Block-Interface-Modules-FLKM-D/dp/B00MEIGAOG/ref=sr_1_1?s=electronics&ie=UTF8&qid=1497833004&sr=8-1&keywords=FLKM-D+9+SUB%2FB|this one]] but it's ridiculously expensive and not even very convenient.) | |
Line 10: | Line 19: |
* Crimping tool | * Extra crimping tool * Extra pin-removal tool * Needle-nosed pliers * Standard hex wrench set * Short hex wrench set |
Line 18: | Line 31: |
* Multimeter (with ohmmeter and diode check function), e.g., [[https://www.monotaro.com/p/2091/7898/?gclid=Cj0KEQjwyZjKBRDu|Fluke 114]] | |
Line 19: | Line 33: |
* DSub9 Breakouts, e.g., [[https://www.amazon.com/Uxcell-Female-Adapter-Terminal-Connector/dp/B01736DOS8/ref=pd_lpo_vtph_147_bs_t_2?_encoding=UTF8&psc=1&refRID=PE9ZD7W1SW6MQ28RT8Q6|male]] and [[https://www.amazon.com/Adapter-Terminal-Connector-Signal-Module/dp/B00WW6YU5G/ref=pd_bxgy_328_img_2?_encoding=UTF8&pd_rd_i=B00WW6YU5G&pd_rd_r=ZQHEDMT34ZQ3AD86MKC7&pd_rd_w=HKAX6&pd_rd_wg=QfWsw&psc=1&refRID=ZQHEDMT34ZQ3AD86MKC7|female]]. One set for use at the rack (dirty) and one set for use in the cleanbbooth (clean). (The one we have is [[https://www.amazon.com/Terminal-Block-Interface-Modules-FLKM-D/dp/B00MEIGAOG/ref=sr_1_1?s=electronics&ie=UTF8&qid=1497833004&sr=8-1&keywords=FLKM-D+9+SUB%2FB|this one]] but it's ridiculously expensive and not even very convenient.) |
VIS Type B Wish List
Parts/Screws
- Cu O-rings for geophones
- As of 2018-04-15
- We have 3 x 150-mm and 4 x 80-mm ones.
- We need 4 x 150-mm and 4 x 80-mm for SR
- We need 3 x 150-mm and 3 x 80-mm if we service the BS geophones.
- We need 1 x 150-mm and 1 x 80-mm spare.
-> ORDER 5 x 150-mm and 4 x 80-mm
- As of 2018-04-15
- Rubber pieces for geophones.
- (3mm * ů77)*9
Tools we'd like soon
Right-angled forceps like these
41-mm wrenches (three if possible) for jacks on tanks, e.g., TOP RS-41.
Tools etc that it would be nice to have
- Extra crimping tool
- Extra pin-removal tool
- Needle-nosed pliers
- Standard hex wrench set
- Short hex wrench set
- Vibrating engraving tool
- More vacuum-compatible tags
- More vacuum-compatible heat shrink
- Bare or Kapton-coated Cu wire for use as cable ties