Differences between revisions 4 and 15 (spanning 11 versions)

VIS Type B Wish List

Parts/Screws

Cu O-rings for geophones
- As of 2018-04-15
  - We have 3 x 150-mm and 4 x 80-mm ones.
  - We need 4 x 150-mm and 4 x 80-mm for SR
  - We need 3 x 150-mm and 3 x 80-mm if we service the BS geophones.
  - We need 1 x 150-mm and 1 x 80-mm spare.
- -> ORDER 5 x 150-mm and 4 x 80-mm
Rubber pieces for geophones.
- (3mm * ≈Ø77)*9

Tools we'd like soon

Right-angled forceps like these
41-mm wrenches (three if possible) for jacks on tanks, e.g., TOP RS-41.

Tools etc that it would be nice to have

Extra crimping tool
Extra pin-removal tool
Needle-nosed pliers
Standard hex wrench set
Short hex wrench set
Vibrating engraving tool
More vacuum-compatible tags
More vacuum-compatible heat shrink
Bare or Kapton-coated Cu wire for use as cable ties

Things already ordered

Multimeter (with ohmmeter and diode check function), e.g., Fluke 114
Nutdriver
DSub9 Breakouts, e.g., male and female. One set for use at the rack (dirty) and one set for use in the cleanbbooth (clean). (The one we have is this one but it's ridiculously expensive and not even very convenient.)

KAGRA/Subgroups/VIS/TypeB/WishList (last edited 2018-04-16 17:07:38 by MarkBarton)

-  ⇤ ← Revision 4 as of 2017-06-19 09:44:23 → 
  Size: 1242
  Editor: MarkBarton
  Comment:
+   ← Revision 15 as of 2018-04-16 17:07:38 → ⇥
  Size: 1978
  Editor: MarkBarton
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 3:
+== Parts/Screws ==
 * Cu O-rings for geophones
  * As of 2018-04-15
   * We have 3 x 150-mm and 4 x 80-mm ones.
   * We need 4 x 150-mm and 4 x 80-mm for SR
   * We need 3 x 150-mm and 3 x 80-mm if we service the BS geophones.
   * We need 1 x 150-mm and 1 x 80-mm spare.
  * -> ORDER 5 x 150-mm and 4 x 80-mm
 * Rubber pieces for geophones.
  * (3mm * ≈Ø77)*9

== Tools we'd like soon ==
 * Right-angled forceps [[http://www.sklarcorp.com/thoracic/grasping-forceps/mixter-right-angle-forceps.html|like these]]
 * 41-mm wrenches (three if possible) for jacks on tanks, e.g., [[https://www.monotaro.com/g/00198495/?t.q=top%20rs-41|TOP RS-41]].
-Line 4:
+Line 19:
- * Crimping tool
+ * Extra crimping tool
 * Extra pin-removal tool
 * Needle-nosed pliers
 * Standard hex wrench set
 * Short hex wrench set
-Line 10:
+Line 28:
- * Right-angled forceps [[http://www.sklarcorp.com/thoracic/grasping-forceps/mixter-right-angle-forceps.html|like these]]
 * Multimeter (with ohmmeter and diode check function)
 * DSub9 Breakouts, e.g., [[https://www.amazon.com/Uxcell-Female-Adapter-Terminal-Connector/dp/B01736DOS8/ref=pd_lpo_vtph_147_bs_t_2?_encoding=UTF8&psc=1&refRID=PE9ZD7W1SW6MQ28RT8Q6|male]] and [[https://www.amazon.com/Adapter-Terminal-Connector-Signal-Module/dp/B00WW6YU5G/ref=pd_bxgy_328_img_2?_encoding=UTF8&pd_rd_i=B00WW6YU5G&pd_rd_r=ZQHEDMT34ZQ3AD86MKC7&pd_rd_w=HKAX6&pd_rd_wg=QfWsw&psc=1&refRID=ZQHEDMT34ZQ3AD86MKC7|female]]. One set for use at the rack (dirty) and one set for use in the cleanbbooth (clean). (The one we have is [[https://www.amazon.com/Terminal-Block-Interface-Modules-FLKM-D/dp/B00MEIGAOG/ref=sr_1_1?s=electronics&ie=UTF8&qid=1497833004&sr=8-1&keywords=FLKM-D+9+SUB%2FB|this one]] but it's ridiculously expensive and not even very good.)
-Line 16:
+Line 31:
+ * Multimeter (with ohmmeter and diode check function), e.g., [[https://www.monotaro.com/p/2091/7898/?gclid=Cj0KEQjwyZjKBRDu|Fluke 114]]
-Line 17:
+Line 33:
+ * DSub9 Breakouts, e.g., [[https://www.amazon.com/Uxcell-Female-Adapter-Terminal-Connector/dp/B01736DOS8/ref=pd_lpo_vtph_147_bs_t_2?_encoding=UTF8&psc=1&refRID=PE9ZD7W1SW6MQ28RT8Q6|male]] and [[https://www.amazon.com/Adapter-Terminal-Connector-Signal-Module/dp/B00WW6YU5G/ref=pd_bxgy_328_img_2?_encoding=UTF8&pd_rd_i=B00WW6YU5G&pd_rd_r=ZQHEDMT34ZQ3AD86MKC7&pd_rd_w=HKAX6&pd_rd_wg=QfWsw&psc=1&refRID=ZQHEDMT34ZQ3AD86MKC7|female]]. One set for use at the rack (dirty) and one set for use in the cleanbbooth (clean). (The one we have is [[https://www.amazon.com/Terminal-Block-Interface-Modules-FLKM-D/dp/B00MEIGAOG/ref=sr_1_1?s=electronics&ie=UTF8&qid=1497833004&sr=8-1&keywords=FLKM-D+9+SUB%2FB|this one]] but it's ridiculously expensive and not even very convenient.)