(1) Suspension health check for IX, EX, PR3, PR2 (IMMT1/2) : (Ushiba-kun and his selected persons)

Sensors' outputs: Spectrum are healthy?, Sensor output positions are in their acceptable ranges?

Transfer function: As we expected? No touching? well decoupling within degrees of freedom?

Actuator function: They works with expected strength? Well repeatability? Decoupling is good (~1/10)?

Offload in each actuators: Positions are not around the edge of the dynamic ranges? Even if they exist, they can be acceptable?

Resonance/motion damping: The Mirror speed is well stabilized below 0. 3um/sec?

Temp sensors in the cryo-suspensions: They are properly obtained ?

(memo) A01: Cable check: Type-A:by R.Takahashi-san), Sato-san has raw data -> OK 空欄部分の意味は？線が切れてるかつながってない状態　→　正常なことを明記お願いします。

Cryo-payload by Ushiba 内外のケーブルチェック:OK FeedThroughのところで、10%以上のばらつき有り。 TBDはスキップ。モデルがないので。

A02 Porality Check Type-A/C-Payload: OK Eddy Current Damping もOK

A03 RubbingCheck Type-A: 〇の意味は？mmでわかりますか？→　全開になってるはず。その時の間隔は？設計上は？F0~ cm orderのはず。最低でもcmあるはず。写真は？ないです。図を入れてわかるようします。 F1~F3は見えないのでEY以外はデータはない。

C-Payload: 目視確認、TM bottom1~4 はせめぎみ。冷やしても広がるセンス。 MN関係は 3.5mm 開けすぎると磁石が当たるので、それを避けるため それ以外は10mm程度 ギャップに関する理由づけもドキュメントにお願いします。 たたいてみて、触れてないこともチェック。

Range and Calibration Type-A: Fishing rod dynamic raange and graphs。軸の単位もお願いします（横軸　ステップ数、縦軸　カウント） LVDT calibrationは金尺以外の方法で、精度を上げられませんか？ Catuator Rangeについては、計測すみで、書き込んでないだけ。効率は伝達関数から見積もるつもりなので、あとで計算。

C-Payload moving mass Range 確認：IXしかできてない。どっちの方向も1mmは動かせる。これで十分なはず。EXではまだやってない。 Actuator Efficiency: 一個を代表して測定

(2)Oplev Check for IX, EX, PR3, PR2 (IMMT1/2) (Yokozawa-kun and his selected persons)

Beam path clearance: well away from obstacle structures? The beams hit around in the center of steering mirrors?

QPD centering: Beams are set around the QPD center? (This centering will satisfy the sensors dynamic ranges in the suspension systems? More offload is necessary?)

Clean signals: No seriously large line noises / and white noises?

Covering: the covers kill light from outside well ?

Beam source degradation: No serious power/beam quality degradation until now?

(3)CAL (ChenDan-kun and his selected person) Please explain what you did after the review.

Beam diameter checks.

Beam path realignment after the accident,

Spectrum health check,

Mirror actuators health check,

(4)Tcam (Yokozawa-kun and ChenDan kun, and Yamamoto-kun?) T-cam system stability,

Image can be obtained without illuminators?

Focus and inclination are proper?

(5)TMSX optical system (Akutsu-kun and his selected persons) Trans image are captured and its image is clear inside the image area?

PD was set to show the max output when we center the green beam on the ETMY mirror?

Clear optical paths on the way to the TMSX detectors(PD/QPDs)?

(6)Baffle PDs (Yokozawa-kun and his selected persons) Outputs are alive, except for one dead one?

Clear signals without any serious line noises and high noise floors?

(7)Baffles (Akutsu-kun and his selected persons) Setting positions: designed positions?

Freely suspended?: position sensors are working properly? (spectrum is OK?)

The resonance damping level is proper?: The proper damping should be realized when the systems are cooled.

temp data: The temp sensors work well?

(8)Vacuum system (Kimura-san / Uchiyama-kun and their selected persons) GV(BS-IXC) is closed?

The vacuum sensors are working well?

The flanges that used to be opened are properly closed? Do you have check lists?

The remedy point check between EXC and TMSX

Not to forget to put level gauges to sense the V-tank height

check of oplev windows, especially.

(9)Vacuum tank cleaning/ lost items

IXA/EXA: chendan-kun, yokozawa-kun

IEXC:Cryo members.

lost items check: miyoki and so on.

(10)Cryo-system (Kimura-san and his selected persons) Temp data are properly obtained?

Insulators are attached properly?

The new cryocoolers are ever tested even for very short duration in the past after setting?

Heaters for windows on the cryo-shields properly works?

(11)Optics and stray light check in POP/REFL/IMCREFL/MCE tables ( Michimura-kun/Akutsu-kun and his selected members?) Maybe this work cannot be finished before 10th, but in 13th week in December, if possible.

Used optics are well understood about their optical properties and damage thresholds?

Stray lights are well dumped?