X-end PCal

Urgent

Excitation port noise

2nd-urgent

Stray light
- Tx PDs detect light even if the AOM input is almost 0.
- Put dumpers
- Module wall will be black coated.

~11/3 first test to inject PCal laser to the X-end test mass

Rx module alignment
- Rx PD done.
- QPD alignment
AOM response measurement
- Done. To be checked periodically.
OL/CL TF measurement
- Done.
- OFS board gain seems strange.
- Strange bump in AA/AI (~6 kHz)
WSK measurement
- Code for WSK measurement analysis
- X-end done, but it may affected by stray light.

~X-arm commissioning line injection

BPM test
Preparation for X-arm commissioning calibration line injection
- Guardian

~O3

RPN measurement
Laser noise measurement
Harmonics noise measurement
VGA noise measurement
Excitation noise measurement
- DGS part seems not noisy, but cause large noise when connected to the OFS.
Peak stability test
Shot noise
Offset input noise
Noise model
Unstable D-sub connection at Tx module
- Some connectors are dead.
Cable arrangement
OFS upgrade
Operation tool preparation

Bonus work

AOM current
- Sometimes over 0.5 V ?
Take care about grounding
Initial laser power just after turned on seems too small ?

Pre-categorization

Y-end PCal

Periscope re-installation

Laser power calibration setting in Toyama Univ.

~Y-arm commissioning

Prepare cross calibration setup and calibrate an integrating sphere

-  ⇤ ← Revision 16 as of 2018-09-20 16:16:16 → 
  Size: 2612
  Editor: chihiro.kozakai
  Comment:
+   ← Revision 28 as of 2018-10-22 12:40:57 → ⇥
  Size: 2333
  Editor: chihiro.kozakai
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 20:
- * TxPD1 repairing 
  * Repaired. To be checked.
 * OFS2 closed loop functionality repairing 
  * Relay is OK. Investigating the cause.
 * DAC noise problem
  * With DAC cable, very large noise and offset are observed. It may be difficult to set working point.
+ * Excitation port noise
-Line 30:
+Line 24:
- * DAC input bias between MEDM and actual
 * Laser remote control
  * Setup done. LAN cable should be replaced to shorter one.
-Line 34:
+Line 25:
+  * Tx PDs detect light even if the AOM input is almost 0.
-Line 35:
+Line 27:
-   * Borrowing 2 from Toyama univ. They has to be returned on 9/19 or 20.
+  * Module wall will be black coated.
-Line 37:
+Line 29:
-~9/11
+~11/3 first test to inject PCal laser to the X-end test mass
-Line 39:
+Line 31:
- * Periscope install
  * Equip picomoters to the mirror

~10/3
 * Complete periscope install
-Line 45:
+Line 32:
-~10/20 first test to inject PCal laser to the X-end test mass
+  * Rx PD done.
  * QPD alignment
-Line 49:
+Line 35:
-  * Check working point is consistent to that in KEK
+  * Done. To be checked periodically.
-Line 51:
+Line 37:
+  * Done. 
  * OFS board gain seems strange.
  * Strange bump in AA/AI (~6 kHz)
-Line 52:
+Line 41:
-  * Modification is required from LIGO's procedure.
-Line 54:
+Line 42:
-  * To be delivered on 9/19 or 20 to Toyama Univ.
  * May have to prepare voltage calibrator to calibrate readout by DGS.
+  * X-end done, but it may affected by stray light.
-Line 60:
+Line 47:
-  * Picomoter setting
-Line 62:
+Line 48:
+  * Guardian
-Line 70:
+Line 57:
+  * DGS part seems not noisy, but cause large noise when connected to the OFS.
-Line 93:
+Line 81:
+ * Periscope re-installation
-Line 95:
+Line 85:
+~Y-arm commissioning

 * Prepare cross calibration setup and calibrate an integrating sphere