1845
Comment:
|
2724
|
Deletions are marked like this. | Additions are marked like this. |
Line 1: | Line 1: |
= Run01 (2018/11/1~11/4) = | = Run01 (2018/11/1~11/3) = |
Line 30: | Line 30: |
RxPD=K1:CAL-PCAL_EX_1_PD_RX_V_DQ | RxPD=K1:CAL-PCAL_EX_1_PD_RX_V_DQ <<BR>><<BR>> Memo: Above 5 channels: . - Sampling rate = 16,384 Hz . . - Type = float (not double!!) <<BR>><<BR>> . |
Line 40: | Line 47: |
* ACO microphone near the Rx module | * ACO microphone near the Rx module<<BR>><<BR>> Memo: Above 3 channels: . - Sampling rate = 2,048 Hz . . - Type = float (not double!!)<<BR>><<BR>> |
Line 45: | Line 56: |
== Memo == | == Unix Time <---> GPS time == |
Line 47: | Line 58: |
* Unix Time = 1541150000 <---> GPS Time = 1225185218 | * Unix Time = 1541150000 <---> GPS Time = 1225185218 (Nov 02, 2018. 09:13:20 UTC = Nov 02, 2018. 18:13:20 JST) * Unix Time = 1541155000 <---> GPS Time = 1225190218 (Nov 02, 2018. 10:36:40 UTC = Nov 02, 2018. 19:36:40 JST) |
Line 49: | Line 61: |
== Hoge == * hoge |
== Other Info. == * PCAL<<BR>> K1:CAL-PCAL_[EX,EY]_[1,2]_PD_[TX,RX,OFS]_V_DQ 16,384 Hz<<BR>> K1:CAL-PCAL_[EX,EY]_TEMP_[TX,RX,LASERINT] 16 Hz<<BR>> K1:CAL-PCAL_[EX,EY]_LASER_TEMPDIOD 16 Hz<<BR>><<BR>> * Baffle PD<<BR>> K1:AOS-[EXC,EYC,IXA]_BAFFLEPD_xxxx 16 Hz<<BR>><<BR>> * EMTX OPLEV<<BR>> K1:VIS-ETMX_TM_OPLEV_xxxx 16 Hz or 2,048 Hz<<BR>><<BR>> * PSL?? (ref caV, MZM, PMC, IMC, ...) * ...(will add more channels later as necessary)... |
Run01 (2018/11/1~11/3)
- Transfer function
- Relative power Noise
- Longtime injection
- Enviroment monitor
- WSK calibration
The measurement condition, measurement "Unix" time (not GPS time), and corresponding channels
Measurement condition |
Unix start time |
Unix finish time |
channels |
Without WSK, Path1 |
1541157539.418005 |
1541157839.8215971 |
TxPD1, OFSPD1, RxPD |
Without WSK, Path2 |
1541157909.4979379 |
1541158200.728071 |
TxPD2, OFSPD2, RxPD |
WSK at Tx module exit, Path1 |
1541156396.084233 |
1541156695.7076631 |
TxPD1, OFSPD1, WSK |
WSK at Tx module exit, Path2 |
1541156891.447325 |
1541157194.656775 |
TxPD2, OFSPD2, WSK |
WSK at Tx module exit, Laser off |
1541157279.23807 |
1541157383.5417781 |
TxPD1, OFSPD1, TxPD2, OFSPD2, WSK |
WSK at Rx module entrance, Path1 |
1541154371.3472719 |
1541154722.988471 |
TxPD1, OFSPD1, WSK |
WSK at Rx module entrance, Path2 |
1541155076.5712309 |
1541155414.8761361 |
TxPD2, OFSPD2, WSK |
WSK at Rx module entrance, Laser off |
1541155503.024539 |
1541155632.5346031 |
TxPD1, OFSPD1, TxPD2, OFSPD2, WSK |
TxPD1=K1:CAL-PCAL_EX_1_PD_TX_V_DQ
TxPD2=K1:CAL-PCAL_EX_2_PD_TX_V_DQ
OFSPD1=K1:CAL-PCAL_EX_1_PD_OFS_V_DQ
OFSPD2=K1:CAL-PCAL_EX_2_PD_OFS_V_DQ
RxPD=K1:CAL-PCAL_EX_1_PD_RX_V_DQ
Memo: Above 5 channels:
- - Sampling rate = 16,384 Hz
- Type = float (not double!!)
Environmental channels
- K1:CAL-PCAL_EX_ACC_RX_OUT_DQ
- TEAC 706 accelerometer on the Rx module
- K1:CAL-PCAL_EX_ACC_TX_OUT_DQ
- TEAC 706 accelerometer on the Tx module
- K1:CAL-PCAL_EX_MIC_OUT_DQ
ACO microphone near the Rx module
- - Sampling rate = 2,048 Hz
- Type = float (not double!!)
- You can check after restart the model at Nov. 3rd (around 17:30 JST)
- Working time is same as PCal maintenance
Unix Time <---> GPS time
Unix Time = 1500000000 <---> GPS Time = 1184035218
Unix Time = 1541150000 <---> GPS Time = 1225185218 (Nov 02, 2018. 09:13:20 UTC = Nov 02, 2018. 18:13:20 JST)
Unix Time = 1541155000 <---> GPS Time = 1225190218 (Nov 02, 2018. 10:36:40 UTC = Nov 02, 2018. 19:36:40 JST)
Other Info.
PCAL
K1:CAL-PCAL_[EX,EY]_[1,2]_PD_[TX,RX,OFS]_V_DQ 16,384 Hz
K1:CAL-PCAL_[EX,EY]_TEMP_[TX,RX,LASERINT] 16 Hz
K1:CAL-PCAL_[EX,EY]_LASER_TEMPDIOD 16 Hz
Baffle PD
K1:AOS-[EXC,EYC,IXA]_BAFFLEPD_xxxx 16 Hz
EMTX OPLEV
K1:VIS-ETMX_TM_OPLEV_xxxx 16 Hz or 2,048 Hz
- PSL?? (ref caV, MZM, PMC, IMC, ...)
- ...(will add more channels later as necessary)...