Contents
KAGRA PEM Channel List
Ondotori
PSL
PEM |
Sensor |
Channel name (_OUT_DQ) |
Picture |
Calibration(unit) |
Memo(S number) |
accelerometer |
TEAC 710 |
K1:PEM-PSL_ACC_TABLE1_Z |
m/s^2 |
||
accelerometer |
TEAC 710 |
K1:PEM-PSL_ACC_TABLE2_Z |
m/s^2 |
||
accelerometer |
TEAC 710 |
K1:PEM-PSL_ACC_TABLE3_Z |
m/s^2 |
||
accelerometer |
KISTLER 8640A5 |
K1:PEM-PSL_ACC_PERI_EXIT |
m/s^2 |
||
accelerometer |
KISTLER 8640A5 |
K1:PEM-PSL_ACC_PERI_REFCAV |
m/s^2 |
||
magnetometer |
MAG13 MCL100 |
K1:PEM-PSL_MAG_LASERRACK_(X|Y|Z) |
T |
MAG13, WF, Distributor, Power |
|
microphone |
(B&K) 4188-A-021 |
K1:PEM-PSL_MIC_CENTER |
Pa |
IMC
PEM |
Sensor |
Channel name (_OUT_DQ) |
Picture |
Calibration(unit) |
Memo(S number) |
microphone |
(B&K) 4188-A-021 |
K1:PEM-IMC_MIC_REFL1 |
[[|pic]] |
Pa |
|
microphone |
(B&K) 4188-A-021 |
K1:PEM-IMC_MIC_REFL2 |
[[|pic]] |
Pa |
Seismometer
Snumber |
Installed Place (ADC port) |
Name |
Channel name (OUT_DQ) |
Unit |
fs [Hz] |
klog |
EXV (IX1, ADC0, 24-26) |
Trillium 12QA |
K1:PEM-IXV_GND_TR120Q_(X/Y/Z)_OUT_DQ |
um/s |
512 |
|
|
EXV (EX1, ADC0, 24-26) |
Trillium 120QA |
K1:PEM-EXV_GND_TR120Q_(X/Y/Z)_OUT_DQ |
um/s |
512 |
|
|
EYV (EY1, ADC0, 24-26) |
Trillium 120QA |
K1:PEM-EYV_GND_TR120Q_(X/Y/Z)_OUT_DQ |
um/s |
512 |
|
|
IXV (IX1, ADC0, 28-30) |
Trillium 120QA |
K1:PEM-IXV_GND_TR120QTEST_(X/Y/Z)_OUT_DQ |
um/s |
512 |
|
|
MCe (IOO1, ADC1, 4-6) |
Trillium compact 120-SV1 |
K1:PEM-IMC_SEIS_MCE_(NS/WE/Z)_OUT_DQ |
cnt |
512 |
|
|
MCi (IOO1, ADC1, 0-2) |
Trillium compact 120-SV1 |
K1:PEM-IMC_SEIS_MCI_(NS/WE/Z)_OUT_DQ |
cnt |
512 |
|
|
Fukuoka Univ. |
Trillium compact 120-SV1 |
??? |
--- |
512 |
|
Selfnoiseのグラフを載せる
Air Environment Sensors
Snumber |
Installed Place (ADC port) |
Name |
Channel name (xxx_OUT_DQ) |
Unit |
Sample rate [Hz] |
IXV (IX1, ADC1, 24-27) |
No.5 |
K1-IXV_WEATHER_{TEMP,HUMD,PRES}_ |
Degree, %, Pa |
128 |
|
IYV (IY1, ADC1, 24-27) |
|
|
|
128 |
|
EXV (EX1, ADC1, 24-27) |
--- |
K1-EXV_WEATHER_{TEMP,HUMD,PRES}_ |
Degree, %, Pa |
128 |
|
EYV (EY1, ADC1, 24-27) |
--- |
K1-EYV_WEATHER_{TEMP,HUMD,PRES}_ |
Degree, %, Pa |
128 |
|
IXC (IX0, ADC0, 16-27?) |
|
|
|
128 |
|
IYC (IY0, ADC0, 20-23) |
No6 |
K1-IYC_WEATHER_{TEMP,HUMD,PRES}_ |
Degree, %, Pa |
128 |
Acording to JGW-T1809269, calibration factor from output voltage to each unit is given with
temp = ( Vout/78/0.001-100)/0.388 [deg_c] humd = Vout/10*100 [%] pressure = Vout/10*300 + 800 [hPa]
Then, "_GAIN" and "_OFFSET" parameters in cds filter of each channels are calculated by above equation with count value not voltage,
Name |
Value |
Unit |
_TEMP_OFFSET |
-1.278e4 |
count |
_HUMD_OFFSET |
0.0 |
count |
_PRES_OFFSET |
4.369e4 |
count |
_TEMP_GAIN |
2.017e-2 |
deg_c/count |
_HUMD_GAIN |
6.104e-3 |
%/count |
_PRES_GAIN |
1.831e-2 |
hPa/count |
,where ransformation coefficient from voltage to adc count is given with c2V = 2.0 * 10/2**15 [V/count], because output signal from sensor is measured with single-end not differential. These parameters are managed by SDF with observe.snap. So, plase do not change this file.
Place Sensor Channel name picture Memo IX0 Temporary K1:PEM-IX0_SENSOR(1-12) pic Will be removed
Place Sensor Channel name picture Memo IY0 Temporary K1:PEM-IY0_SENSOR(1-12) pic Will be removed
Model snapfile managed date klog k1pemiy0 observe.snap Dec 03 09:49:41 2018 k1pemix1 observe.snap Nov 28 19:27:27 2018 k1pemex1 observe.snap Nov 28 19:25:46 2018 k1pemey1 observe.snap Nov 30 17:15:59 2018 Temporary channels in IX0
Temporary channels in IY0
SDF