1649
Comment:
|
2065
|
Deletions are marked like this. | Additions are marked like this. |
Line 2: | Line 2: |
== DC status on each mode's GDS_TP screen should be 0x0. == |
|
Line 24: | Line 26: |
|| x4000|| It is OK. Data is being sent and you can leave it. A master IOP gets this error when the timing synchronization is fucked up. || || x2000|| It is OK. When the master IOP's timing is not synchronized properly, their slave models show this code.|| || 0x2 || The real time model is not sending data to the data concentrator machine, k1dc0. Go to (1) || || blank || Channels are not registered to send to k1dc0. Go to (2) || (1) When DC status is 0x2 |
|| x4000|| It is OK. Data is being sent and you can leave it. There is some synchronization error. || || x2000|| It is OK. Data is being sent and you can leave it. There is some synchronization error.|| || 0x2bad || Bad. The real time model is not sending data to the data concentrator machine, k1dc0. Go to (1) || || blank || Bad. Channels are not registered to send to k1dc0. Go to (2) || === (1) When DC status is 0x2bad === |
Line 35: | Line 38: |
(2) When DC status is blank | === (2) When DC status is blank === ==== 1. First check ==== make sure the model's channel list is registered in {{{master}}}. {{{ t cd fb emacs master }}} Check if 1. tpchn_modelname.par 1. MODELNAME.ini are written in the file. ==== 2. If master is ok, but still blank, or, if you changed master file ==== |
Line 42: | Line 59: |
{{{daqd}}} process will automatically start up again, and the DAC status will be cleared. If it did not work, try to reboot the data concentrator: | {{{daqd}}} process will automatically start up again, and the DAC status will be cleared. ==== 3. If neither above did not work ==== Reboot the data concentrator: |
Line 47: | Line 67: |
==== 4. Rebooting did not work ==== Call Osamu or Keiko. |
Check if the real time models are sending data to DAQ
DC status on each mode's GDS_TP screen should be 0x0.
1. Open sitemap on an workstation
$sc $medm sitemap.adl
2. Open CDS screen
3. Open GDS_TP screen of each model (blue buttons)
4. Check that "DC Status" is 0x0
DC status |
What to do |
0x0 |
Good status! |
x4000 |
It is OK. Data is being sent and you can leave it. There is some synchronization error. |
x2000 |
It is OK. Data is being sent and you can leave it. There is some synchronization error. |
0x2bad |
Bad. The real time model is not sending data to the data concentrator machine, k1dc0. Go to (1) |
blank |
Bad. Channels are not registered to send to k1dc0. Go to (2) |
(1) When DC status is 0x2bad
ssh <FE macehine name such as k1pr0> sudo /etc/init.d/mx_stream restart
mx_stream process will automatically start up again, and the DAC status will be cleared.
(2) When DC status is blank
1. First check
make sure the model's channel list is registered in master.
t cd fb emacs master
Check if
- tpchn_modelname.par
- MODELNAME.ini
are written in the file.
2. If master is ok, but still blank, or, if you changed master file
ssh k1dc0 ps -ef | grep daqd
Check the process number of daqd. There may be two or three and pick the first and left number (###).
kill ###
daqd process will automatically start up again, and the DAC status will be cleared.
3. If neither above did not work
Reboot the data concentrator:
ssh k1dc0 sudo reboot
Wait patiently until k1dc0 restarts.
4. Rebooting did not work
Call Osamu or Keiko.