Differences between revisions 13 and 139 (spanning 126 versions)
Revision 13 as of 2019-12-16 08:47:00
Size: 5557
Editor: guiguo.ge
Comment:
Revision 139 as of 2020-04-07 12:03:16
Size: 5321
Comment:
Deletions are marked like this. Additions are marked like this.
Line 1: Line 1:
= For collaborator shifts =
Line 2: Line 4:
    * When FPMI cannot keep lock state for over 10 minutes or cannot got to lock state ---> call operation shift members.

 * Collaboration shift routine tasks

 . <<TableOfContents(2)>>

== Control Room Overview ==
* IFO Monitor: shows the status of the Main Interferometer
 . {{attachment:IFO Monitor.png||}}
* CCD Monitor:
 . {{attachment:ccd monitor.png||}}
* DAQ/VIS status:
 . {{attachment:vis status.png||}}
* PEM Monitor: Room temperature/ Vacuum pressure
 . {{attachment:Pem.jpg||}}
* Time: show GPS/UTC/JST time
 . {{attachment:GPS t ime.jpg||}}
 * Operator shift table in [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=10914|JGW-M1910914]]
 * Some information for collaborator shifts in [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=9380|JGW-M1809380]]
Line 22: Line 8:
== How to use Guardian ==
=== Accessing to the guardian screen ===
 . In the desktop, you can click on the sitemap.
 . {{attachment:IFO Monitor.png||}}
 . {{attachment:IMG_4929.jpg||}}
 . {{attachment:IMG_4929.jpg||width="430"}}
 . In the sitemap, you can click on the link for the guardian overview screen.
 . {{attachment:IMG_4929.jpg||width="430"}}
------
== Collaboration shift routine tasks ==
Line 31: Line 11:
 . {{attachment:IMG_4929.jpg||width="430"}}
 . {{attachment:IMG_4929.jpg||width="430"}}
 . {{attachment:IMG_4929.jpg||width="430"}}
 . {{attachment:IMG_4929.jpg||width="430"}}
=== Knowing the current state and requested state ===
 . {{attachment:guardian_howto4.png||height="281",width="434"}}
 1. When FPMI cannot keep locked state for over 10 minutes or cannot got to lock state
  ---> call operator shift members
   * contact person (operator shift) on the day is listed with '''PHONE NUMBER''' around white board in the control room or see the link [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=10914|JGW-M1910914]] (no phone number in this list)
Line 38: Line 15:
=== How to request a state ===
 . Click on the gray bar in the middle.<<BR>> {{attachment:guardian_howto.png||height="298",width="433"}} <<BR>> Then, choose the desired state.<<BR>> {{attachment:guardian_howto2.png||height="299",width="434"}}
 * Write "Log book" ([[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=11124|JGW-E1911124]]) on the desk in the control room.
  * Check Guardian status for 5 items, LSC, VIS, IO, Green laser and ALS. Instruction is in below.
  * Put check mark every 2 hours.
  * Write down everything you noticed.
   * Example: lock lost, earthquake, somebody entered mine etc.
 * Please write [[http://klog.icrr.u-tokyo.ac.jp/osl/|klog]]: [[http://klog.icrr.u-tokyo.ac.jp/osl/]] before you leave control room.
  * Writing [[http://klog.icrr.u-tokyo.ac.jp/osl/|klog]] is very important. This is only one tool which can show the status in the control room to outside.
  * Account name and password are shown on the white board in the control room.
 * Leave message on "Takeover note" ([[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=5032|JGW-T1605032]]) on the desk in the control room if you have something to tell to the next shift.
 * Improve this wiki page if you had something you did not understand well and you found what it is.
  1. Search "KAGRA wiki" in google and access to KAGRA top page.
  * Go to ERun top page on the second line of KAGRA Top page, and go to "Collaborator shift manuals". That page is this manual.
  * Login KAGRA wiki, and press "Edit" button around the top left.
   * Account name and password are shown on the white board in the control room.
Line 41: Line 30:
== How to know the status of the interferometer ==
 . Look at one of the TV monitor in the control room. If "ON", it is in OPERATION mode.
 {{attachment:obs_state.png||height="233",width="465"}} <<BR>>If "OFF", check the guardian overview screen<<BR>> {{attachment:guardian_howto3.png||height="281",width="434"}} <<BR>>Check the state of LSC_MICH. First check if the request state of LSC_MICH is OPERATION. If it is not, request OPERATION.<<BR>> {{attachment:guardian_howto4.png||height="281",width="434"}}
 . If the state is ''READY, ENGAGE_SERVO, ENGAGE_BOOST, MICH_LOCKED, CALIBRATION_INJECTION'', or ''ACTUATORCAL_INJECTION'', the interferometer is now on the way to be OPERATION state. It will be ready soon. <<BR>> /!\ ''' If it does not enter OPERATION state in a few mins. Call the interferometer experts.'''<<BR>> Check the status of ''IMC_LOCK, VIS_BS, VIS_PR2, VIS_PR3''. (Note that ''VIS_PRM'' is not used for now, so just ignore it) <<BR>>For IMC_LOCK, every thing should be green and IMC should be back automatically. <<BR>> {{attachment:IMC_guardian.png||height="293",width="453"}} <<BR>> For example, this is how the IMC_LOCK guardian should normally look like.<<BR>> {{attachment:IMC_guardian_status.png||height="281",width="407"}} <<BR>> /!\ '''If it does not come back in ~ 10 mins, call interferometer/IOO experts.'''<<BR>> For VIS_PR2 and VIS_BS, the state should be ALIGNED. If inot, a notification "please reset Watch Dog!" will show up, and the state is in TRIPPED. In that case, go to the next section to know how to reset Watch Dog. <<BR>> For VIS_PR3, the state should be DAMPED. If it is not, a notification "please reset Watch Dog!" will show up, and the state is in TRIPPED. In that case, go to the next section to know how to reset Watch Dog.
------
------
Line 46: Line 33:
== How to reset Watch Dogs ==
 0. Request LSC_MICH to be READY by Guardian.
== 1. Interferometer locking status screen ==
 * Please check the interferometer locking screen at the front monitor in the control room first. If the status is not "LOCKED", something might happen.
 * If PRFPMI cannot keep "LOCKED" state for over 10 minutes or cannot got back to "LOCKED" state, please contact operator shift.
 * If it is '''LOCKED''', please take notes IMC output power, BNS range, beam status.
Line 49: Line 38:
 0. Open Sitemap (from Terminal, type "mk" and press return).  * '''comment from a shift taker''' Note that "LOCKED" and "OBSERVING" are different. The above check should be replaced with "OBSERVING" status.
Line 51: Line 40:
 0. Click VIS  {{attachment:2020-02-27 4.58.16.png||width="800"}}
Line 53: Line 42:
 0. Click the suspension of which you want to reset Watch Dog
 {{attachment:VISALL.png||width="407"}} <<BR>>
Line 56: Line 43:
 0. Go to PRs case or BS case ------
== 2. Check list of the interferometer ==
Line 58: Line 46:
=== PRs case ===
 4. Request SAFE by Guardian
=== How to access to the guardian screen ===
 *On the desktop, you can click the ''sitemap'' icon.
Line 61: Line 49:
 4. Open "DETAILS" at bottom right,
 {{attachment:PRTOP.png||width="300"}} <<BR>>
  . and you will find PRs overview screen
 {{attachment:PR.png||width="800"}} <<BR>>
 {{attachment:112.png||width="700"}}
Line 66: Line 51:
 4. Click WATCHDOG
  . If something is red, press here to reset.
 {{attachment:PRWD.png||width="400"}} <<BR>>
 *In the sitemap, you can click on the link for the guardian overview screen.
 {{attachment:116.png||width="800"}}
Line 70: Line 54:
 4. Click DACKILL (see the picture above, PRs overview sceen)
  . If it is not green, press reset.
 {{attachment:DACKILL.png||width="200"}} <<BR>>
Line 74: Line 55:
 4. Click Coil Driver WD (picture above, PRs overview sceen) Check if everything is green. If there are red signs, push corresponding WD Pulse ON button and then OFF button
 {{attachment:PR_CDWD.png||width="800"}} <<BR>>
Line 77: Line 56:
 4. Request DAMPED. For PR2, ~ 10 seconds after the state becomes DAMPED, request ALIENED. === 2-1. Check if the LSC_LOCK Guardian at OBSERVATION state ===
Line 79: Line 58:
 4. ~ 10 seconds after the suspension gets in a nominal state, request LSC_MICH to be OPERATION.  * Please check the "LSC_LOCK" is in "OBSERVATION" mode. If not, please contact operator shift.('''Please put a red box for LSC_LOCK''')
 {{attachment:116.png||width="800"}}
Line 81: Line 61:
=== BS case ===
 4. Request SAFE by Guardian
Line 84: Line 62:
 4. Open "Payload" at bottom center,
 {{attachment:BSTOP.png||width="250"}} <<BR>>
  . and you will find BS payload overview screen
 {{attachment:BSpayload.png||width="800"}} <<BR>>
=== 2-2. Check if all of VIS Guardians are at ALIGNED state ===
Look at Guardian Overview
 {{attachment:VIS guardian.png||height="",width="700"}}
 
OR you can see the VIS status on the Monitor
 {{attachment:VIS guardian 2.png||height="",width="600"}}
 * If the Guardian is at TRIPPED state, you should [[http://gwwiki.icrr.u-tokyo.ac.jp/JGWwiki/KAGRA/Commissioning/Phase1/Operation/ShiftManual#How_to_reset_Watch_Dogs|reset Watch Dogs (WDs)]]('''Content of this document should be replaced with new one'''), OR call operation shift members (contact person TBD).
Line 89: Line 70:
 4. Click WATCHDOG If something is red, press here to reset.
 {{attachment:PRWD.png||width="400"}} <<BR>>
=== 2-3. Check the IO Guardian ===
{{attachment:IO guardian.png||height="",width="800"}}
Line 92: Line 73:
 4. Click DACKILL (see the picture above for BS overview screen) If it is not green, press reset.
 {{attachment:DACKILL.png||width="200"}} <<BR>>
IO Guardian should at PROVIDING_STABLE_LIGHT state, if not call operation shift members '''ASAP!!!'''(contact person TBD).
Line 95: Line 75:
 4. Click Coil Driver WD (see the picture above for BS overview screen) Check if everything is green. If there are red signs, push corresponding WD Pulse ON button and then OFF button
 {{attachment:PR_CDWD.png||width="800"}} <<BR>>
=== 2-4. Check the Green Laser status ===
 * See if the shutter is on or not. If the background color is green, the shutter is ok/open (red means the shutter is closed).
Line 98: Line 78:
 4. Request DAMPED. For PR2, ~ 10 seconds after the state becomes DAMPED, request ALIENED. {{attachment:shutter.png||height="",width="800"}}
Line 100: Line 80:
 4. ~ 10 seconds after the suspension gets in a nominal state, request LSC_MICH to be OPERATION.
 * see if K1: ALS-X (Y)_ARM_INPUT_OUT is more than 0.7

{{attachment:0.7.png||height="",width="680"}}

=== 2-5. Check if ALS_PLLX/ALS_PLLY Guardian is at PLL_LOCK state ===

{{attachment:PLLXY1.png||height="",width="880"}}


------
== Control Room Overview ==
 * IFO Monitor: shows the status of the Main Interferometer
 * '''The following control room image should be changed with new one.'''
 . {{attachment:IFO1.png||width="800"}}


 * CCD Monitor:
 . {{attachment:CCD.jpg||height="1000"}}


 * DAQ/VIS status:
 . {{attachment:vis status.png||height="800"}}


 * PEM Monitor: Room temperature/ Vacuum pressure
 . {{attachment:Pem.jpg||width="800"}}


 * Time: show JST/UTC/GPS time
 . {{attachment:GPS t ime.jpg||width="800"}}

For collaborator shifts


Collaboration shift routine tasks

  1. When FPMI cannot keep locked state for over 10 minutes or cannot got to lock state
    • ---> call operator shift members

      • contact person (operator shift) on the day is listed with PHONE NUMBER around white board in the control room or see the link JGW-M1910914 (no phone number in this list)

  2. Write "Log book" (JGW-E1911124) on the desk in the control room.

    • Check Guardian status for 5 items, LSC, VIS, IO, Green laser and ALS. Instruction is in below.
    • Put check mark every 2 hours.
    • Write down everything you noticed.
      • Example: lock lost, earthquake, somebody entered mine etc.
  3. Please write klog: http://klog.icrr.u-tokyo.ac.jp/osl/ before you leave control room.

    • Writing klog is very important. This is only one tool which can show the status in the control room to outside.

    • Account name and password are shown on the white board in the control room.
  4. Leave message on "Takeover note" (JGW-T1605032) on the desk in the control room if you have something to tell to the next shift.

  5. Improve this wiki page if you had something you did not understand well and you found what it is.
    1. Search "KAGRA wiki" in google and access to KAGRA top page.
    2. Go to ERun top page on the second line of KAGRA Top page, and go to "Collaborator shift manuals". That page is this manual.
    3. Login KAGRA wiki, and press "Edit" button around the top left.
      • Account name and password are shown on the white board in the control room.



1. Interferometer locking status screen

  • Please check the interferometer locking screen at the front monitor in the control room first. If the status is not "LOCKED", something might happen.
  • If PRFPMI cannot keep "LOCKED" state for over 10 minutes or cannot got back to "LOCKED" state, please contact operator shift.
  • If it is LOCKED, please take notes IMC output power, BNS range, beam status.

  • comment from a shift taker Note that "LOCKED" and "OBSERVING" are different. The above check should be replaced with "OBSERVING" status.

    2020-02-27 4.58.16.png


2. Check list of the interferometer

How to access to the guardian screen

  • On the desktop, you can click the sitemap icon.

    112.png

  • In the sitemap, you can click on the link for the guardian overview screen.

    116.png

2-1. Check if the LSC_LOCK Guardian at OBSERVATION state

  • Please check the "LSC_LOCK" is in "OBSERVATION" mode. If not, please contact operator shift.(Please put a red box for LSC_LOCK) 116.png

2-2. Check if all of VIS Guardians are at ALIGNED state

Look at Guardian Overview

  • VIS guardian.png

OR you can see the VIS status on the Monitor

  • VIS guardian 2.png

  • If the Guardian is at TRIPPED state, you should reset Watch Dogs (WDs)(Content of this document should be replaced with new one), OR call operation shift members (contact person TBD).

2-3. Check the IO Guardian

IO guardian.png

IO Guardian should at PROVIDING_STABLE_LIGHT state, if not call operation shift members ASAP!!!(contact person TBD).

2-4. Check the Green Laser status

  • See if the shutter is on or not. If the background color is green, the shutter is ok/open (red means the shutter is closed).

shutter.png

  • see if K1: ALS-X (Y)_ARM_INPUT_OUT is more than 0.7

0.7.png

2-5. Check if ALS_PLLX/ALS_PLLY Guardian is at PLL_LOCK state

PLLXY1.png


Control Room Overview

  • IFO Monitor: shows the status of the Main Interferometer
  • The following control room image should be changed with new one.

  • IFO1.png

  • CCD Monitor:
  • CCD.jpg

  • DAQ/VIS status:
  • vis status.png

  • PEM Monitor: Room temperature/ Vacuum pressure
  • Pem.jpg

  • Time: show JST/UTC/GPS time
  • GPS t ime.jpg

KAGRA/EngineeringRun/ER191217_24/Shift (last edited 2020-04-07 12:03:16 by OsamuMiyakawa)