Stuff for Type B to do in March 2018 while waiting for deliveries

Possible schedule of selected tasks from below

Week of 3/5
- Finish any remaining SR2 SF stuff. (Enzo+2)
- Get SRM mushroom installed (Hirata-san, Kimura-san, Sawada-san)
- BF filter rebuild (Hirata-san+1)
  - Move filter table into SRM area.
  - Get additional heavy table.
  - Disassemble two filters
Week of 3/12
- Rack work (Enzo+1)
  - Find boxes for SR3 and SRM at Mozumi
  - Add boxes to SR3 and SRM racks
  - Do SR3 and SRM in-rack cables and labeling
  - Do SR3 in-air cables.
- BF filter rebuild continued (Hirata-san+1)
  - Characterize 10 blades
  - Choose two matched sets
  - Rebuild two filters
Week of 3/19 (Mitaka)
- Make two sets of IM OSEMs
- Make in-air pico adapter cable
- Set up Dummy BS prism removal.
Week of 3/26
- SF Setup, Test
  - Set up SR3 assembly frame, weights.
  - Bring in remaining two SFs.
  - Remeasure load capacity, check for tilted keystone.
  - Install Cu segments on cap.
  - Wire and test LVDT.

Tasks that we have the necessary items to do in March

Make box of stuff to send to Mitaka
- OSEM coils and connectors for assembly.
- Pico in-air adapter parts.
- BS soaking cup.
- Anti-feedthrough adapter parts.
- Geophone parts?
Build four geophone assemblies (Okutomi-kun has built five):
- Have most parts:
  - Four sets of canister parts (body, neck, head).
  - Five geophones.
  - Three circuit boards - probably more exist but need to find.
  - 20 x M8*35 (need 4*16=64)
  - 35 x M8*30 (need 4*8=32)
  - 4 x Viton disks (need 4? or 8?)
  - 123 M8 washers (need 4*24=96)
Assemble more OSEMs.
- Have 6 wound coils and connectors at Kamioka (one set, for SR3).
- Have 6 more at Mitaka.
Set up SR3 and SRM racks.
- Miyakawa-san gave us an empty rack for SR3 => can add boxes and do internal cabling and labels.
- SR3 rack position is decided (on -X,+Y corner of SR3 cleanbooth) => can do in-air cabling from rack to assembly frame.
- Miyakawa-san will soon give us an empty rack for SRM and decide position => will be able to do set-up.
Disassemble broken top filters
- Set up heavy table in SRM area (first floor, -X side).
- Find jig and blade tensioning screw.
- Remove blades from #3 (in SRM area).
- Store #3 in box.
- Remove floor panel in SRM second floor.
- Crane #1 (in SR3 area) to SRM area.
- Remove blades from #1.
- Put test weights on table.
BF rebuild - Hirata-san + 1
- Move BS Test Hang BF to tent and remove blades. (These blades are for BS-BF and will not be used again.)
- Find SR-BF blades that were removed to free up a BF base for the BS Final Hang.
- Move BF with tilted keystone to tent and remove blades.
- Characterize all SR-BF blades and choose two similar groups.
- Rebuild two filters.
Etc
- Move all SFs to cleanbooth and inspect for keystone tilt and/or other issues.
- Make one set of in-air pico splitter cables (triple and double) for SRM.
- Make three in-air stepper splitter cables for SR2, SR3 and SRM.
- Soak the sapphire prisms off the dummy BS for reuse on the SRM metal mass.
- Do buoyancy calculation (see LIGO-T1100616).
- Set up SR2 Guardian.
- Install damping filters for SR2.
Stuff to have done by other teams
- Add mushroom top to SRM tank.
- Put up safety bars