3969
Comment:
|
4468
|
Deletions are marked like this. | Additions are marked like this. |
Line 31: | Line 31: |
|| '''COIL''' || '''efficiency [um/cnt]''' || || H1 || || || H2 || || || H3 || || || || || || V1 || || || V2 || || || V3 || || |
[[http://klog.icrr.u-tokyo.ac.jp/osl/?r=4846|klog#4846]] || number# || linear range [cnt] || calibration factor [um/cnt] || for which? || noise level at 10 Hz || || || || || || || || No#53 || IM-V1 || 0.078991 || 1600-12500 || || || No#54 || IM-V2 || 0.079014 || 1480-12600 || || || No#55 || IM-V3 || 0.083248 || 1500-12000 || || || || || || || || || No#56 || IM-H1 || 0.074347 || 1390-14200 || || || No#57 || IM-H2 || 0.070756 || 1370-14700 || || || No#58 || IM-H3 || 0.088711 ||1450-11100 || || |
SR3 suspension information
position
FARO measurement
GAS default height (LVDT readout)
- BF GAS LVDTIN:
- F1 GAS LVDTIN:
- F0 GAS LVDTIN:
suspension parameters
resonant frequencies
position of the COM
calculated from the resonant frequencies.
sensor & actuator parameters
Oplev calibration
OSEM calibration
IM-stage
number# |
linear range [cnt] |
calibration factor [um/cnt] |
for which? |
noise level at 10 Hz |
|
|
|
|
|
No#53 |
IM-V1 |
0.078991 |
1600-12500 |
|
No#54 |
IM-V2 |
0.079014 |
1480-12600 |
|
No#55 |
IM-V3 |
0.083248 |
1500-12000 |
|
|
|
|
|
|
No#56 |
IM-H1 |
0.074347 |
1390-14200 |
|
No#57 |
IM-H2 |
0.070756 |
1370-14700 |
|
No#58 |
IM-H3 |
0.088711 |
1450-11100 |
|
GAS-LVDT calibration
Sensor |
Efficiency [um/cnt] |
F0-LVDT |
|
F2-LVDT |
|
F3-LVDT |
|
IP-LVDT calibration
Sensor |
Efficiency [um/cnt] |
LVDT H1 |
|
LVDT H2 |
|
LVDT H3 |
|
Geophone calibration
Frequency response
Geophone's frequency response to the ground velocity:
- Ge: Generator constant [V/(m/s)]
- η: Intrinsic damping ratio
- ω0: Resonant angular frequency [rad/s]
Sensor |
S/N |
Generator constant (nominal) [V/(m/s)] |
Damping ratio (estimated) |
Resonant frequency [Hz] |
GEO H1 |
# |
|
|
|
GEO H2 |
# |
|
|
|
GEO H3 |
# |
|
|
|
Noise
Sensor |
Noise [m/rtHz] @ 0.1 Hz |
Noise [m/rtHz] @ 10 Hz |
GEO H1 |
|
|
GEO H2 |
|
|
GEO H3 |
|
|
Calibration
Converted displacement [um] = 3.052 x 10-4 [V/cnt] / HGEO(ω) / (gainPreamp) x (DC cutoff) x 1/s (m/(m/s)) x 106
actuation polarization
TM-stage
COIL |
sign |
H1 |
|
H2 |
|
H3 |
|
H4 |
|
IM-stage
COIL |
sign |
H1 |
|
H2 |
|
H3 |
|
|
|
V1 |
|
V2 |
|
V3 |
|
IP-stage
COIL |
sign |
H1 |
|
H2 |
|
H3 |
|
Diagonalization matrix
- ACC2EUL
H1 |
H2 |
H3 |
To: |
** |
|
|
|
** |
|
|
|
** |
|
|
|
- LVDT2EUL
H1 |
H2 |
H3 |
To: |
|
|
|
Long. |
|
|
|
Trans. |
|
|
|
Yaw |
- EUL2COIL
Long. |
Trans. |
Yaw |
To: |
|
|
|
H1 |
|
|
|
H2 |
|
|
|
H3 |
actuation efficiency
Stepper motor
See also: Stepper motor setup
Epics channel name: K1:STEPPER_***_IP |
|||||
Driver IP address: 10.68.150.** |
|||||
Motor 0 |
Motor 1 |
Motor 2 |
Motor 3 |
Motor 4 |
Motor 5 |
|
|
|
|
<blank> |
<blank> |