Agenda/Minutes of the VIS Meeting on 2017/6/16

2017/6/16 13:30 -

Participants:

Progress report

Schedule Chart : (PDF,MPP)

• Type-A:
• Type-B:
• Type-Bp:

Type-A (Takahashi)

Past week report

Installation in Y-end:

12th(Mon)

• Adjusted the tilt of BF by moving masses.
• Checked geometry around the BF.

13th(Tue)

• Adjusted the height of damper ring for the BF.
• Adjusted the yaw rotation of BF.
• Attached the LVDT coils and checked the movable range.
• Attached the cable clamps onto the TF.
• Removed the wire clamp.

14th(Wed)

• Tuned the TF to frequency less than 0.2Hz changing the compression of blades.
• Assembled the cables for BF damper.
• Cabled from the F1 to the TF.

15th(Thu)

• Made flip cables.
• Cabled around the BF damper.
• Tuned the LVDT driver.
• Checked the assembly of geophone pods.

16th(Fri)

• Prepared for the power outage.

Plan for coming weeks

• Check of the BF damper.
• Cabling to the feedthroughs.
• Setting of the ACCs.
• Preparation in X-end.

Type B (Mark)

Past week report

Plan for coming weeks

Type-Bp (Shoda)

Past week report

• Mirror preparation
  • We glued the wire breakers and flags on the PR2 mirror on last Friday, but they detached when I checked on Sunday.
  • Therefore, we tried the gluing again on Monday, and checked Tuesday evening. But they did not fixed again.
  • We tried again on Thursday, and it is curing time now. This time, we have put more glue on them.
• Other preparation
  • We assembled PR2 BF LVDTs and PRM BF LVDTs. They are all calibrated.
  • We almost finished cabling between the field rack and clean room for PR2.
  • PRM circuits are also almost ready. Not cabled yet.
• PR3 measurement
  • Fujii-kun measured the properties of PR3.
  • We found the one of the coil driver does not working well. The current for PR3/PRM rack and IOO rack was not enough. The problem of the current was fixed with Nakano-kun, but the driver might have been driven with saturated status, which might cause the problem.

  • Miyakawa-san is asking us to report the circuits problem via e-mails when they occur in order to record them.

Plan for coming weeks

• Mirror/RM hanging (if they are properly fixed...)

IMMT (Ohishi)

Past week report

Plan for coming weeks

Watchdog system (Tanaka)

Past week report

Plan for coming weeks

Other site works

• Preparation for the power outage by 6/16
• Preparation for the PR floor re-work by 6/16
• 6/19: Power outage
• 6/21: Safety lecture after the morning briefing
• 6/21 11:30 - 12:30: Crane inspection

• 6/20 -24: BS & PR booth: lighting installation (BS and PR2 area 6/23 afternoon)

• 6/22-23: PR area: floor fix
• 6/26-30: PR area: stainless steel flooring
• 6/28: Maintenance of the rapid charger for the electric vehicles

Safety

• Incidents:
• Foreseen risks
  • Type-A:
  • Type-B:
  • Type-Bp:

Discussion

Travel Plans

• Travel (Week of 6/19):
  • Takahashi: 20-23
  • Shoda: 20-23
  • Mark: 19-23
  • Fabian: 20-22
  • Okutomi: 20-23
  • Fujii:
  • Ishizaki: 20-23
  • Hirata: 20-23
  • Sato: 20-23
  • Enzo: 20-22
  • Ohishi:
  • Tanaka:
  • Akiyama(Hosei): 20-23
  • Hashimoto(Hosei): 20-22
• Travel (Week of 6/26):
  • Takahashi:
  • Shoda:
  • Mark:
  • Fabian:
  • Okutomi:
  • Fujii:
  • Ishizaki:
  • Hirata:
  • Sato:
  • Enzo:
  • Ohishi:
  • Tanaka:
  • Akiyama(Hosei):
  • Hashimoto(Hosei):

Next meeting

On 2017/6/23(Fri) Next F2F: 6/30(Fri)