Agenda/Minutes of the VIS Meeting on 2017/6/23

2017/6/23 13:30 -

Participants:

Progress report

Schedule Chart : (PDF,MPP)

• Type-A: A week delay in Y-End. On schedule for X-End but the X-End schedule need to be shortened.
• Type-B: Updating the real BS installation schedule.
• Type-Bp:

Type-A (Takahashi)

Past week report

Installation in Y-end/X-end:

20th(Tue)

• Recovered from the power outage.
• Opend the chamber.
• Tuned the TF by changing the compression of blades again.
• Disassembled the bridge frame.

21th(Wed)

• Continued the tuning of TF to 0.2Hz.
• Released the IP and adjusted the tilt of the IP base.
• Checked the FR for TF. The FR was not working.
• Made the cables for ACC.
• Transported some items from the Y-end to the X-end.

22th(Thu)

Y-end

• Tuned the IP roughly. The frequency is 80mHz.
• Adujusted the centering of IP by the tilt of IP base and the motor sliders.
• Started cabling from the TF to the feedthroughs.

X-end

• Cleaned the floor.
• Covered the floor by SUS sheets.

Plan for coming weeks

• Setting of the BF damper.
• Cabling to the feedthroughs.
• Setting of the ACCs.
• Preparatioin in X-end.

Type B (Mark)

Past week report

Plan for coming weeks

Type-Bp (Shoda)

Past week report

• The wire breaker still refused to be attached.
  • We tried two more times (on Tuesday and Wednesday). The 2nd wire breaker was attached. But the 1st wire breaker still have not been glued.
  • We tried gluing again today at IYC clean booth.
• The temperature change by 3 degrees during the power outage, which corresponds to about 2 mm height change per 1 GAS filter. And the temperature seems to change more if the power is not turned on for longer time.
• PRM optical bench intermediate ring and damper ring are prepared and set inside the PRM chamber.
• PRM cabling is almost ready at outside the clean booth.
• BIO system is implemented into the PR3 model, but we need help of Kokeyama-san or Miyakawa-san in order to increase the BIO card more than 10.

Plan for coming weeks

• Please glued. Then mirror hanging.

IMMT (Ohishi)

Past week report

• Drawing some parts related with IMMT; coil holder support, etc.

Plan for coming weeks

• 6/27(Tue)-28(Wed) Magnets and standoffs gluing at Kashiwa

Watchdog system (Tanaka)

Past week report

• Examination of experimental preamplifier circuit fabrication. -->

  • I completed the performance test of the PreAmp. for use on the KAGRA side.However,data analysis is in progress.Report(JGW-E1706850)PDF

• Creation of extended I/O PCB(plot type (With the Main 4ch WDS box and I/O box,I/O board For relay).-->

  • Estimate --> completed.

  • Waiting for purchase of goods.

Plan for coming weeks

• Creation of extended I/O PCB(plot type (With the Main 4ch WDS box and I/O box,I/O board For relay).-->Ongoing.

• Examination of experimental preamplifier circuit fabrication. -->Ongoing.

• Adjustment of experiment schedule etc. in the KAGRA side start.

Other site works

• 6/26-30: PR area: stainless steel flooring
• 6/28: Maintenance of the rapid charger for the electric vehicles

Safety

• Incidents:
• Foreseen risks
  • Type-A:
  • Type-B:
  • Type-Bp:

Discussion

• Cable purchase

Travel Plans

• Travel (Week of 6/26):
  • Takahashi: 26 - 29
  • Shoda: 26 - 29
  • Mark: 26 - 29 (?)
  • Fabian: 26 - 29 (?)
  • Okutomi: 26 - 29
  • Fujii:
  • Ishizaki: 26 - 29
  • Hirata: 26 - 29 (?)
  • Sato: 26 - 29
  • Enzo: 27 - 29 (?)
  • Ohishi:
  • Tanaka:
  • Akiyama(Hosei): 27 - 29
  • Hashimoto(Hosei): 26 - 29
• Travel (Week of 7/3):
  • Takahashi:
  • Shoda:
  • Mark:
  • Fabian:
  • Okutomi:
  • Fujii:
  • Ishizaki:
  • Hirata:
  • Sato:
  • Enzo:
  • Ohishi:
  • Tanaka:
  • Akiyama(Hosei):
  • Hashimoto(Hosei):

Next meeting

On 2017/6/30(Fri) Next F2F: 7/??