Agenda/Minutes of the VIS Meeting on 2017/7/21

2017/7/21 13:30 -

Participants:

Progress report

Schedule Chart : (PDF,MPP)

• Type-A:
• Type-B:
• Type-Bp:

Type-A (Takahashi)

Past week report

[X-end]

19th(Wed)

• Transported some items from Y-end to X-end.

20th(Thu)

• Preassembled the BF damper.
• Measured the weight of DP and BF.
• Replaced the receptacles in the BF.
• Replaced the blades for FR in the BF.
• Replaced the cable clamps on the BF
• Set the release sensors for the BF.

21st(Fri)

• Adjusted the rotation of frame lock.
• Hooked the short maraging wire to the BF. The DP was suspended from the BF.
• Tuned the BF roughly. The optimal frequency was about 0.5Hz. More compression is necessary.

[Y-end]

18th(Tue)

• Cabled from the cryo-payload to the BF.
• Closed the EYV chamber completely, The o-ring was replaced.

19th(Wed)

• Checked the cable connection. One cable was disconnected.
• Unplugged in-air cables from feedthroughs.
• Closed the cross tube completely.

20h(Thu)

• The brackets for the corrugate tube were replaced. Measured the height of the EYV chamber.

21st(Fri)

• Plugged in-air cables to feedthroughs.
• Started evacuation of the chamber.

Plan for coming weeks

• Monitering behavior of the Type-A tower in Y-end.
• Installation of the bottom filter in X-end.

Type B (Mark)

Past week report

Plan for coming weeks

Type-Bp (Shoda)

Past week report

• IM TF measurement
  • IM TFs seem to be OK.
  • The coupling from IML to TMP could not be observed with Oplev with a good coherence. The coupling ration should be less than 10^-1 rad/m with a rough estimation. (Some parameters need to be checked.)
• All parts are assembled on the suspension.
  • BF/BFRM parts are assembled except that BF/IM/TM are not suspended from the SF.
  • Cabling is almost done.
  • Berndy male pins are running out.

Plan for coming weeks

• Suspend the BF and blow from the SF, and adjust the weight and the balance
• TF check
• Installation preparation
• Prepare for PRM Traverser shipping.

IMMT (Ohishi)

Past week report

Plan for coming weeks

Watchdog system (Tanaka)

Past week report

• Creation of extended I/O PCB(plot type (With the Main 4ch WDS box and I/O box,I/O board For relay).-->

• Order electronic parts -->No delivery(Coop Univ.Tokyo).

• Order PCB's(Ex-I/O Interface and relative PCB's) -->Delivery complete.

• Looking for board manufacturer(Manufacturer who makes PCB manufacturing and mounting(including parts procurement).
• Start of preliminary experiment at KAGRA site.

• Start production of equipment(As soon as parts are delivered).-->Start PCB check.

Plan for coming weeks

• Experiment schedule(for KAGRA site).-->24th( Tokyo-->Toyama ),25-26th full(KAGRA),27th(Reserve and Toyama --> Tokyo )

Other site works

• 7/25 - 26: Y-arm water pump exchange
• End of Aug. to Nov.: Mozumi entrance will be closed

Safety

• Incidents:
• Foreseen risks
  • Type-A:
  • Type-B:
  • Type-Bp:

Discussion

Travel Plans

• Travel (Week of 7/24):
  • Takahashi: 24 - 28
  • Okutomi: 24 - 28
  • Sato: 24 - 28
  • Ishizaki: 24 - 28
  • Mark: 24 - 28
  • Fabian: 24 - 28
  • Hirata: 25 - 28
  • Enzo:
  • Shoda: 24 - 27
  • Ohishi:
  • Fujii:
  • Tanaka: 25 - 26 (27)
  • Kuroki: 25 - 28
  • Hashimoto(Hosei): 24 - 27
  • Yoshioka (Toyama): 25,26,28
• Travel (Week of 7/31):
  • Takahashi:
  • Okutomi:
  • Sato:
  • Ishizaki:
  • Mark:
  • Fabian:
  • Hirata:
  • Enzo:
  • Shoda:
  • Ohishi:
  • Fujii:
  • Tanaka:
  • Hashimoto(Hosei):
  • Yoshioka (Toyama): 1,2,4

Next meeting

On 2017/7/28(Fri)