|
Size: 1194
Comment:
|
Size: 2363
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 2: | Line 2: |
| 2020/5/15 14:00 - | 2020/5/15 14:00 - |
| Line 6: | Line 6: |
| Participants: | Participants: |
| Line 15: | Line 15: |
| * Integrated ３D model of each Type-A tower.(JGW-D2011655) * According to the 3D model, it was found that the placement of the BF Dumper is offset by 5 degrees from the beam line (EX, EY only) [[attachment:ETM BF Dumper.pdf]] |
|
| Line 16: | Line 19: |
| * Type-B paper: I wrote a [[http://gwwiki.icrr.u-tokyo.ac.jp/JGWwiki/KAGRA/Subgroups/VIS/TypeB/PaperTODOlist|TO DO list]] which roughtly works as an outline. Thank you Shoda-san for your comments! * In case it's not possible to measure the quality factors due to time constraints related to the pandemic, we can cite the prototype paper instead where similar measurements were reported. * Include long term drift observation of the optic orientation using the oplev. * Check what Terence did about inertial damping. He wrote good klog entries but there's still not enougn information to understand the detail. I will ask him once he becomes avilable to us sometime next month. * Inertial damping: I have been checking what Takanori did and I've been trying to adapt it to the case of SR2 using the Matlab simulation. I have questions but I'm not ready to ask. I will do it sometime soon via e-mail. |
|
| Line 21: | Line 30: |
| * KAGRA is under the suspended mode until 31st May. | * KAGRA is in the suspended mode until 31st May. |
| Line 23: | Line 32: |
| * O3c is still under discussion between LVK ([[https://paper.dropbox.com/doc/Plan-for-the-long-OR-brake--AxxlJFvK1IGJjqrG5nfdHfGXAQ-KqexeqMaCA7DITFGxA5ih|Plan]], [[https://www.dropbox.com/s/hoadb73fdyah02c/Post-O3%20task.xlsx?dl=0|Sheet]]). | |
| Line 24: | Line 34: |
| * Type-A: Shoda(Mechanical), Lucia(Performance), Fujii(Sensor collection). | * Type-A: Shoda(Mechanics), Lucia(Performance), Fujii(Sensor collection). |
| Line 26: | Line 36: |
| * Towards O3c * [[https://paper.dropbox.com/doc/Plan-for-the-long-OR-brake--AxxlJFvK1IGJjqrG5nfdHfGXAQ-KqexeqMaCA7DITFGxA5ih|Plan]] * [[https://www.dropbox.com/s/hoadb73fdyah02c/Post-O3%20task.xlsx?dl=0|Sheet]] |
|
| Line 34: | Line 41: |
| On 2020/5/22(Fri) | * On 2020/5/22(Fri) |
Agenda/Minutes of the VIS Meeting on 2020/5/15
2020/5/15 14:00 -
Participants:
Progress report
General
Type-A
- Integrated ３D model of each Type-A tower.(JGW-D2011655)
According to the 3D model, it was found that the placement of the BF Dumper is offset by 5 degrees from the beam line (EX, EY only) ETM BF Dumper.pdf
Type-B
Type-B paper: I wrote a TO DO list which roughtly works as an outline. Thank you Shoda-san for your comments!
- In case it's not possible to measure the quality factors due to time constraints related to the pandemic, we can cite the prototype paper instead where similar measurements were reported.
- Include long term drift observation of the optic orientation using the oplev.
- Check what Terence did about inertial damping. He wrote good klog entries but there's still not enougn information to understand the detail. I will ask him once he becomes avilable to us sometime next month.
- Inertial damping: I have been checking what Takanori did and I've been trying to adapt it to the case of SR2 using the Matlab simulation. I have questions but I'm not ready to ask. I will do it sometime soon via e-mail.
Type-Bp
Type-C
Controls
Electronics
Post O3
- KAGRA is in the suspended mode until 31st May.
Only measurements, which can be done remotely, are available (Request).
- Papers
- Type-A: Shoda(Mechanics), Lucia(Performance), Fujii(Sensor collection).
- Type-B: Fabian
Safety
Discussion
Travel Plans
Next meeting
- On 2020/5/22(Fri)