Size: 2479
Comment:
|
Size: 2622
Comment:
|
Deletions are marked like this. | Additions are marked like this. |
Line 1: | Line 1: |
= Wide Angle Baffle at EYC = | = Wide Angle Baffle at IYC = |
Line 3: | Line 3: |
||<<MonthCalendar(,2018,10)>>||<<MonthCalendar(,2019,1)>>|| | ||<<MonthCalendar(,2018,10)>>||<<MonthCalendar(,2018,11)>>||<<MonthCalendar(,2018,12)>>||<<MonthCalendar(,2019,1)>>|| |
Line 34: | Line 34: |
P23 | P23 (ABCD -> S/N#2564, EFGH -> S/N#360) |
Line 36: | Line 36: |
||A||75 ohm|| Thermometer || V- || Green || || || ||B||75 ohm|| Thermometer || V+ || Black || || || ||C||4 ohm|| Thermometer || I- || Red || || || ||D||4 ohm|| Thermometer || I+ || Yellow || || || ||E||75 ohm|| Thermometer || V- || Green || || || ||F||75 ohm|| Thermometer || V+ || Black || || || ||G||4 ohm|| Thermometer || I- || Red || || || ||H||4 ohm|| Thermometer || I+ || Yellow || || || |
||A||75 ohm|| Thermometer || V- || Green || WAB || || ||B||75 ohm|| Thermometer || V+ || Black || WAB || || ||C||4 ohm|| Thermometer || I- || Red || WAB || || ||D||4 ohm|| Thermometer || I+ || Yellow || WAB || || ||E||75 ohm|| Thermometer || V- || Green || Structure || || ||F||75 ohm|| Thermometer || V+ || Black || Structure || || ||G||4 ohm|| Thermometer || I- || Red || Structure || || ||H||4 ohm|| Thermometer || I+ || Yellow || Structure || || |
Wide Angle Baffle at IYC
|
|
|
|
Links to knowledge
Calculations regarding the back-scattering of different Wide Angle Baffle designs (Zeidler)
Personal calc of WAB's stray light noise by Akutsu; due to several uncertain parameters there are several results and no one would know the actual effect!
Heat links positions (by Obuchi) fmkopgehpapgdkcc.png
Task list
Note: some of the tasks can be done in parallel.
Place/install the WAB suspension
Align the position of WAB -> take WAB back to nominal position, put off protectors)
horizontal alignment
yaw alignment
Move it to the saving mode.
Back to the nominal position.
Attach heat links
4 soft heat links to WAB
1 heat link btwn the top and the structure
Attach 2 thermometers
- Set revised blocks under the base plate.
Pin Assignment
P23 (ABCD -> S/N#2564, EFGH -> S/N#360)
Pin Name |
Resistance |
Equipment |
Assign |
Comment1 |
Comment2 |
Connection |
A |
75 ohm |
Thermometer |
V- |
Green |
WAB |
|
B |
75 ohm |
Thermometer |
V+ |
Black |
WAB |
|
C |
4 ohm |
Thermometer |
I- |
Red |
WAB |
|
D |
4 ohm |
Thermometer |
I+ |
Yellow |
WAB |
|
E |
75 ohm |
Thermometer |
V- |
Green |
Structure |
|
F |
75 ohm |
Thermometer |
V+ |
Black |
Structure |
|
G |
4 ohm |
Thermometer |
I- |
Red |
Structure |
|
H |
4 ohm |
Thermometer |
I+ |
Yellow |
Structure |
|
Note that the pin arrangement (or the naming) is mirrored compared with that of in IXC! Rather, I guess this IXC's would be correct.