Differences between revisions 1 and 12 (spanning 11 versions)
⇤ ← Revision 1 as of 2021-03-26 09:53:36 →
Size: 565
Editor: YutaMichimura
Comment:
← Revision 12 as of 2021-04-15 13:48:19 → ⇥
Size: 2924
Editor: YutaMichimura
Comment:
Deletions are marked like this. Additions are marked like this.
Line 2: Line 2:
Participants: Participants: Satoshi Tanioka, Kenta Tanaka, Naoki Koyama, Chiaki Hirose, Kentaro Somiya, Kiwamu Izumi, Koji Nagano, Marc Eisenmann, Masayuki Nakano, Naoki Aritomi, Shoichi Oshino, Tomotada Akutsu, Yua Michimura
Line 14: Line 14:
 * Interferometer alignment
  * For O4, ISS setup will be removed from IMMT1T table but IMMT1 oplev setup will remain. We should take care if it affect IMMT1T QPD signals.
  *
Line 19: Line 22:
 * Other recent topics   * Are we going to remove ISS setup at IMMT1T?
  * Any upgrades necessary for IMC ASC?
  * Can we automate the beam centering with Tcams for reproducibility?
  * Any thoughts on why PRMI alignment has to be done before Yarm alignment?
  * Are there better ways for daily alignment?
  * What are the steps necessary for engaging WFS/QPD loops in O4?
 * Other recent topics related to ISC
  * Fiber noise cancellation improvement plans for ALS [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=12769|JGW-T2112769]] (Tanioka)
  * Non-polarized beam splitter https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=10506 [Michimura]
   * IMC REFL: Thorlabs BSW11 are used (Ts=~40%)
   * IMC TRANS: Probably Thorlabs BSW11 are used
   * REFL: Note that p-pol is coming out from the chamber. Newport 10Q20HBS.33S (for s-pol) are used. Thin film polarizers are also used and there seems to be a confusion.
   * POP: Newport 10Q20HBS.33S (for s-pol) is used. S-pol/P-pol power ratio can be confused with this BS.
   * POS: No BS placed.
   * AS: p-pol is coming out from the chamber. We agreed to use HWP to make them s-pol and to use Newport 10Q20HBS.33S (for s-pol). But this solution might be confusing.
   * Planning to order non-polarized BS soon.
  * In-vac steering mirrors: https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=12592 [Michimura]
   * For some steering mirrors, p-pol beam
    * STM1, STM2, POM1, POM2 around IFI (PYD-20 is used)
    * steering mirrors after OFI
    * PYD-20 has a transmission
     * T < 70ppm at 0 deg for s-pol (measured)
     * T < 25ppm at 30 deg for s-pol (measured)
     * T < 5ppm at 45 deg for s-pol (measured)
     * T ~ 1000pppm at 45 deg for p-pol (specsheet)
    * Also, specs of POP_POM and POS_POM for IR p-pol needs to be investigated
  * Optical table cover for TRX/TRY and IMC REFL/IMC TRANS: [[KAGRA/subgroup/ifo/MIF/Minutes20210412|Review page]] [Michimura]

ISC Meeting on 2020/04/13 13:00 - 15:00

Participants: Satoshi Tanioka, Kenta Tanaka, Naoki Koyama, Chiaki Hirose, Kentaro Somiya, Kiwamu Izumi, Koji Nagano, Marc Eisenmann, Masayuki Nakano, Naoki Aritomi, Shoichi Oshino, Tomotada Akutsu, Yua Michimura

Zoom meeting: https://zoom.us/j/6676627462

Your time zone: https://www.timeanddate.com/worldclock/fixedtime.html?iso=20210413T0400

Next meeting

TBD

back to Meetings page

Minutes

  • Interferometer alignment
    • For O4, ISS setup will be removed from IMMT1T table but IMMT1 oplev setup will remain. We should take care if it affect IMMT1T QPD signals.

Agenda

  • Summary of interferometer alignment in O3GK and RSE commissioning JGW-T2112594 (Michimura)

  • Discussion on how to proceed for O4
    • Are we going to remove ISS setup at IMMT1T?
    • Any upgrades necessary for IMC ASC?
    • Can we automate the beam centering with Tcams for reproducibility?
    • Any thoughts on why PRMI alignment has to be done before Yarm alignment?
    • Are there better ways for daily alignment?
    • What are the steps necessary for engaging WFS/QPD loops in O4?
  • Other recent topics related to ISC

    • Fiber noise cancellation improvement plans for ALS JGW-T2112769 (Tanioka)

    • Non-polarized beam splitter https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=10506 [Michimura]

      • IMC REFL: Thorlabs BSW11 are used (Ts=~40%)
      • IMC TRANS: Probably Thorlabs BSW11 are used
      • REFL: Note that p-pol is coming out from the chamber. Newport 10Q20HBS.33S (for s-pol) are used. Thin film polarizers are also used and there seems to be a confusion.
      • POP: Newport 10Q20HBS.33S (for s-pol) is used. S-pol/P-pol power ratio can be confused with this BS.
      • POS: No BS placed.
      • AS: p-pol is coming out from the chamber. We agreed to use HWP to make them s-pol and to use Newport 10Q20HBS.33S (for s-pol). But this solution might be confusing.
      • Planning to order non-polarized BS soon.

    • In-vac steering mirrors: https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=12592 [Michimura]

      • For some steering mirrors, p-pol beam
        • STM1, STM2, POM1, POM2 around IFI (PYD-20 is used)
        • steering mirrors after OFI
        • PYD-20 has a transmission

          • T < 70ppm at 0 deg for s-pol (measured)

          • T < 25ppm at 30 deg for s-pol (measured)

          • T < 5ppm at 45 deg for s-pol (measured)

          • T ~ 1000pppm at 45 deg for p-pol (specsheet)
        • Also, specs of POP_POM and POS_POM for IR p-pol needs to be investigated

    • Optical table cover for TRX/TRY and IMC REFL/IMC TRANS: Review page [Michimura]

KAGRA/subgroup/ifo/MIF/Minutes20210413 (last edited 2021-07-13 11:03:45 by YutaMichimura)