|
Size: 613
Comment:
|
Size: 3894
Comment:
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 1: | Line 1: |
| = Optical Lever = | = Optical Lever (Room Temperature) = |
| Line 4: | Line 4: |
| '''[[../|..Up]]''' | |
| Line 7: | Line 8: |
| Optical lever for LCGT-SAS system | Sensing local motions including --(longitudinal dof and)-- all alignment dofs (pitch, yaw and roll) of any mirrors supported by vibration isolation system. <!> Note on the operating temperature: here the system is assumed to be utilized at room temperature, not in cryogenic temperature. |
| Line 10: | Line 15: |
| * Spec. for vacuum chambers * Any... |
TBD; just see the links below. |
| Line 14: | Line 18: |
=== Receiver and Transmitter === |
|
| Line 23: | Line 24: |
| * | * ITM chambers (X,Y) * ETM chambers (X,Y) * PRC chambers (PRC, PR2, PR3) * SRC chambers (SRC, SR2, SR3) * MC chambers (MC1, MC2...) |
| Line 26: | Line 31: |
| TBD | * Sensor noise should be less than xxx. * Sensor's dynamic range should be greater than xxx. * At least horizontal degrees of freedom (X,Y) * Preferably a vertical sensor (Z) and side * The sensors have to be rigidly mounted on the ground so that these are useful for remembering the position of the mirror and recording the drifts. |
| Line 29: | Line 38: |
| TBD | Each optical lever consists of an optical system, a frontend circuit, and a human interface software. The optical system consists of the following parts: a light source, optical fibers, a focusing telescope, viewport windows, a detector, and pylons which support the focusing telescope and the detector. The frontend circuit is TBD. Maybe we need analog cables (and what kind of connector should we use?), whitening filters and antialiasing filters. Maybe the matrix circuit will be realized using the digital systems, but in commissioning phase, we will need analog matrix. The human interface software is TBD, which shows the mirrors' dofs monitored by Optical Levers. |
| Line 31: | Line 46: |
| === Light source === For the light source, proposed candidates are * superluminous LED (SLED) or * laser light source as LIGO. === Optical Fibers === The optical fibers transmit the light from the source to the focusing telescope. === Focusing Telescopes === TBD. Moving linear stage with micrometer and some optical components like collimators? === Viewport windows === See also the [[../Viewport1|viewport subsystem]]. It should be transparent for the light source wavelength. There should be no wedge; otherwise the multiple spots of light would be problematic. === Detectors === The detector will be an ordinary quadruplet photocondutive circuit with QPD. The noise level at '''xxx''' Hz should be '''xxx''' m/Hz^2^ === Pyrons === The pyrons must be designed. |
|
| Line 35: | Line 72: |
| == Procurement process and plans == TBD <<Anchor(Links)>> |
|
| Line 36: | Line 78: |
| * [[https://dcc.ligo.org/cgi-bin/DocDB/ShowDocument?docid=29666&version=1|LIGO-T1000746-v1, Viewports Subsystem Final Design Document]] | <!> Some of the LIGO documents listed below are '''NOT''' public; to access them, you may need your own LSC account. * [[https://dcc.ligo.org/cgi-bin/private/DocDB/ShowDocument?docid=22686|LIGO-M1000343, Advanced LIGO Review Committee Report: Test Mass Optical Lever FDR]] * [[https://dcc.ligo.org/cgi-bin/private/DocDB/ShowDocument?docid=15032|LIGO-T1000517, Optical levers Final Design Review for test masses, recycler mirrors and HAM optical benches]] * [[https://dcc.ligo.org/cgi-bin/private/DocDB/ShowDocument?docid=70690|LIGO-G1100961, Long-Term Stability Test for aLIGO Optical Levers]] * [[http://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=418|JGW-G1100418, LCGT vacuum chamber envelope study]] * [[https://dcc.ligo.org/cgi-bin/private/DocDB/ShowDocument?docid=15271|LIGO-T1000533, Super-luminescent LED 21 and 50 day trend analysis]] * [[https://dcc.ligo.org/cgi-bin/private/DocDB/ShowDocument?docid=13338|LIGO-T1000390, Trade-off Study for the Optical Lever Light Source]] * [[https://dcc.ligo.org/cgi-bin/private/DocDB/ShowDocument?docid=11010|LIGO-T1000219, Test mass optical levers preliminary design]] |
Optical Lever (Room Temperature)
Related subgroups: VIS, IOO, MIF, VAC, CRY...
Contents
Scope
Sensing local motions including longitudinal dof and all alignment dofs (pitch, yaw and roll) of any mirrors supported by vibration isolation system.
Note on the operating temperature: here the system is assumed to be utilized at room temperature, not in cryogenic temperature.
Applicable Documents
TBD; just see the links below.
General Description
Naming Conventions
TBD
Locations
- BS chamber
- ITM chambers (X,Y)
- ETM chambers (X,Y)
- PRC chambers (PRC, PR2, PR3)
- SRC chambers (SRC, SR2, SR3)
- MC chambers (MC1, MC2...)
Requirements
- Sensor noise should be less than xxx.
- Sensor's dynamic range should be greater than xxx.
- At least horizontal degrees of freedom (X,Y)
- Preferably a vertical sensor (Z) and side
- The sensors have to be rigidly mounted on the ground so that these are useful for remembering the position of the mirror and recording the drifts.
Characteristics
Each optical lever consists of an optical system, a frontend circuit, and a human interface software. The optical system consists of the following parts: a light source, optical fibers, a focusing telescope, viewport windows, a detector, and pylons which support the focusing telescope and the detector. The frontend circuit is TBD. Maybe we need analog cables (and what kind of connector should we use?), whitening filters and antialiasing filters. Maybe the matrix circuit will be realized using the digital systems, but in commissioning phase, we will need analog matrix. The human interface software is TBD, which shows the mirrors' dofs monitored by Optical Levers.
Light source
For the light source, proposed candidates are
- superluminous LED (SLED) or
- laser light source as LIGO.
Optical Fibers
The optical fibers transmit the light from the source to the focusing telescope.
Focusing Telescopes
TBD. Moving linear stage with micrometer and some optical components like collimators?
Viewport windows
See also the viewport subsystem. It should be transparent for the light source wavelength. There should be no wedge; otherwise the multiple spots of light would be problematic.
Detectors
The detector will be an ordinary quadruplet photocondutive circuit with QPD. The noise level at xxx Hz should be xxx m/Hz2
Pyrons
The pyrons must be designed.
Inspection plans
TBD
Procurement process and plans
TBD
Links
Some of the LIGO documents listed below are NOT public; to access them, you may need your own LSC account.