• KAGRA
• Subgroups
• VIS
• VISMinutes20161028

Agenda/Minutes of the VIS Meeting on 2016/10/28

2016/10/28 13:30 - @Mitaka F2F.

Participants: Takahashi, Mark, Sato, Tanaka, Okutomi, Ishizaki, Aso, Enzo, Hirata, Akutsu, Shoda, Fujii, Raffaele

Progress report

Schedule Chart (PDF,MPP) To Be Updated

Type-A (Takahashi)

• Minutes of Type-A Meeting

• Pre-isolator: The top filter was mounted onto the IP. The shaft screw of motor was not matching to the slider for fishing rod. New shafts were ordered.
• EQ stop, release sensor, dummy payload: Production is on going.
• BF damper: Open bidding is on 9th November.
• Maraging wire: Hirata-san made 2D drawings. The wires will be ordered soon.
  • Asking CRY to check the rod design for suspending the cryogenic payload. Set a deadline for the answer (Takahashi)
• Installation: Making assembly drawings for the installation procedure document. The review is held on 4th November.

Type B (Mark)

• Type B Past Week Summary
  • Fabian, Mark and Liu-kun did BS installation at Kamioka:
    • Debugged the issue with the BF keystone being tilted enough to cause rubbing on the yoke for the magnets. It was solved by moving the yoke ≈1 mm taking advantage of the oversized holes.
    • Measured the height of the payload as a function of trim mass. The BF spring seems to have a slightly lower load capacity and a rather higher spring constant than when it was remeasured by Hirata-san.
      • Now the resonant frequency is around 0.6 Hz as opposed to the 0.4 Hz when it was tuned.
      • Continue the test hanging with this configuration, but check if 0.6 Hz is OK or not from the viewpoint of the vibration isolation performance with simulation.
      • Hirata-san will come to Kamioka from Nov. 7 to 11 to check the BF.
    • Removed IM trim mass to set the average height of the keystone to the CAD value.
    • Moved IM trim mass around to set the pitch of the dummy BS and the roll of the IM.
    • Constructed the rest of the IRM around the IM.
  • Hirata-san
    • Prepared to get quotes for different types of "flying saucer" cable clamps (D1504530, D1605625, D1605734).
    • Finished BS assembly drawings (in-tank version) and sent to Saito-sensei).
    • Finished maraging rod 3D models and drawings (for Type A)
    • Modified top plate drawings for PRM inner frame.

Type-Bp (Shoda)

• BFRM
  • Still waiting for ordering process.
• Stab Flags
  • Waiting for the cost estimation.
• Assembly frame
  • Asking cost estimate. Also asking to upgrade the assembly frame in the end of November.
• Install procedure
  • pictures how to install whole suspension chain into the chamber is circulated.
    • We will ask the company about the accerelation of the crane, the chain block, and the lever block. According to their information, we will buy a chain block or a lever block and test them at Mitaka.
• Flag removing jig.
  • The model is made by Shoda and approved by Hirose-san. Now the 2D drawing is being made.
• Disassembly of PR3
  • To be done from Nov. 8 to 11. Enzo and Kasuya-san will join.

IMMT (Ohishi)

• Put a report here

Watchdog system (Tanaka)

• Conference material PCB Design Draft version.(Oct 21th 2016)PDF

• Design and preparation(investigation of procurement) for production.PDF

• Will show the design at the next AEL meeting.

Safety

• No issue

Discussion

• Suspension naming convention (Okutomi)
  • We decided on the following convention

Type-A:
F0 - F1 - F2 - F3 - BF - PF - (MN) - IM - OP
Type-B:
F0 - F1 - BF - IM - OP
Type-Bp:
F1 - BF - IM - OP

• Type-Bp installation tool: Lever block or Chain block (Shoda)
  • Will contact manufacturers of those tools if they have data on the operation shocks.

Site work plan for the next week

• Mon:
• Tue:
• Wed:
• Thu:
• Fri:

Travel Plans

• Travel (Week of 10/31):
  • Takahashi:
  • Shoda:
  • Mark:
  • Fabian:
  • Okutomi:
  • Fujii:
  • Ishizaki:
  • Hirata:
  • Sato:
  • Ohishi:
• Travel (Week of 11/7):
  • Takahashi: 7-9 (Extended chief meeting/Fire drill/Accelerometer test)
  • Shoda: 7-11 (Extended chief meeting/Fire drill/PR3 disassemble)
  • Mark: 8 - 11 (Fire drill/BS)
  • Fabian:
  • Okutomi: 7 - 11 (Extended chief meeting/Fire drill/Accelerometer test/Realtime code)
  • Fujii: ? (Fire drill)
  • Ishizaki:
  • Hirata: 8 - 11 (Fire drill/BS)
  • Sato: 7-9 (Fire drill/Accelerometer test)
  • Enzo: 8-11 (PR3 disassembly)
  • Ohishi:

Next meeting

On 2016/11/4(Fri)

VIS F2F: Nov. 18, Dec. 2