Differences between revisions 85 and 96 (spanning 11 versions)

LCGT Auxiliary Optics Subsystem (AOS)

Contents

LCGT Auxiliary Optics Subsystem (AOS)

Objectives

The objectives of the subgroup "Auxiliary Optics System" (AOS) is to have the other LCGT subgroups design and complete the auxiliary optics that physically, logically and consistently glue the main parts of the LCGT interferometer together.

General Description

Most of the AOS shall be fit to the vacuum chambers that had been already determined when the AOS group was established. Even if the vacuum chamber was not designed considering the space allocated for AOS, AOS are required for fully operating LCGT, so we shall, by any means, pack them into the vacuum chambers if required.

References

Aux. opt. list from MIF's point of view	Layout Meeting
Optical Parameters	Parameter Meeting
LCGT SVN	Terminology	Discussion with Rana 2010

Subsystems

Stray Light Control
- Including beam baffles, output Faraday isolators, and calculation of BRDF of test masses...
IR Pick-off and transmit telescopes
Green Transmit Telescopes
- Auxiliary laser-locking system itself should be considered in MIF or IOO. The effort of system designing should be separated from that of engineering and fabricating from the WBS point of view (or what-you-call system engineering) even if the person assigned to both is the same.
Optical Lever
- Optical lever is a kind of local sensors, but unlike other local sensors, it requires long beam lines as lever's arms, thus this should be considerd in AOS.
Initial Alignment
CCD monitors
Viewports on Vacuum Chambers
Beam Shutters
Beam Targets in Arms
Beam Mode Profiler
Other local sensors/monitors/actuators?
Any other optics, outside breadboard,...
Squeezing system??
Maybe mainly VIS group's charge and not AOS's:
- Local Sensors and Actuators (LIGO's OSEM-like things utilized in vibration isolation system)
- Violine mode sensors or Wire position sensors (utilized in vibration isolation system or in noise-hunting phase)

Meetings

LCGT-AOS Meetings

-  ⇤ ← Revision 85 as of 2011-08-29 06:53:44 → 
  Size: 2800
  Editor: TomotadaAkutsu
  Comment:
+   ← Revision 96 as of 2011-09-03 09:41:50 → ⇥
  Size: 2932
  Editor: TomotadaAkutsu
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 9:
-All the AOS shall be fit to the vacuum chambers that had been already determined when the AOS group was established.
Even if the vacuum chamber was not designed for considering the space allocated for AOS, AOS are required for fully operating LCGT, so we should pack them into the vacuum chambers by any means.
+Most of the AOS shall be fit to the vacuum chambers that had been already determined when the AOS group was established.
Even if the vacuum chamber was not designed considering the space allocated for AOS, AOS are required for fully operating LCGT, so we shall, by any means, pack them into the vacuum chambers if required.
 Line 22:
-   * <!> Auxiliary laser-locking system itself should be considered in MIF or IOO. The effort of system design should be separated from that of engineering and fabrication from the WBS point of view (or what-you-call system engineering) even if the person assigned to both is the same.
+   * <!> Auxiliary laser-locking system itself should be considered in MIF or IOO. The effort of system designing should be separated from that of engineering and fabricating from the WBS point of view (or what-you-call system engineering) even if the person assigned to both is the same.
 Line 26:
- * [[LCGT/subgroup/AOS/InitialAlign1|Initial Alignment System]]
+ * [[LCGT/subgroup/AOS/InitialAlign1|Initial Alignment]]
 Line 29:
- * [[LCGT/subgroup/AOS/Shutter1|Beam Shutter]]
+ * [[LCGT/subgroup/AOS/Shutter1|Beam Shutters]]
 * [[LCGT/subgroup/AOS/BeamTarget1|Beam Targets in Arms]]
 * [[LCGT/subgroup/AOS/BeamModeProfiler1|Beam Mode Profiler]]