Size: 5141
Comment:
|
← Revision 62 as of 2018-10-24 19:00:52 ⇥
Size: 6011
Comment:
|
Deletions are marked like this. | Additions are marked like this. |
Line 1: | Line 1: |
= Transmission Monitor's Vibration Isolation Stage: preparation (TMS-VIS) = | = Transmission Monitor's Vibration Isolation Stage for X: preparation (TMS-VISX) = |
Line 28: | Line 28: |
||'''Sensor'''|| polarity || calibration factor || || LVDT V1 || negative ||-0.149 [um/cnt] || || LVDT V2 || positive || 0.138 [um/cnt] || || LVDT V3 || negative ||-0.135 [um/cnt] || || LVDT V1 || negative || 0.154 [um/cnt] || || LVDT V2 || positive || 0.146 [um/cnt] || || LVDT V3 || negative || 0.150 [um/cnt] || |
* V: postive means that the LVDT outputs positive counts when TMS-VIS moves upward, and so the calibration factors are set. * H: postive means that the LVDT outputs positive counts when TMS-VIS moves positive yaw (counter clock wise from top view), and so the calibration factors are set. ||'''Sensor'''|| Serial#|| polarity || calibration factor || || LVDT V1 ||#4 || negative ||-0.149 [um/cnt] || || LVDT V2 ||#5 ||positive || 0.138 [um/cnt] || || LVDT V3 ||#6 ||negative ||-0.135 [um/cnt] || || LVDT H1 ||#1 ||positive || 0.154 [um/cnt] || || LVDT H2 ||#2 ||positive || 0.146 [um/cnt] || || LVDT H3 ||#3 ||positive || 0.150 [um/cnt] || |
Line 54: | Line 56: |
||'''Actuator'''|| polarity || || COIL V1 || positive || || COIL V2 || positive || || COIL V3 || positive || || COIL V1 || negative || || COIL V2 || positive || || COIL V3 || positive || |
* V: postive means upward (TMS-VIS moves in upward by inputting positive value to the act coils from MEDM) * H: positive means plus yaw (TMS-VIS moves in counter clock wise from top view by inputting positive value to the act coils from MEDM) ||'''Actuator'''|| polarity ||Serial#|| || COIL V1 || positive ||#10 || || COIL V2 || positive ||#11 || || COIL V3 || positive ||#12 || || COIL H1 || negative (obsolete) -> ||#7(obsolete)-> #2 || || COIL H2 || positive (obsolete)-> ||#8(obsolete) -> #4 || || COIL H3 || positive (obsolete) -> ||#9(obsolete)-> #5 || Unfortunately, the actuator coils serial#7, 8, and 9 were broken during the transportation from Mitaka to Xend; their serial number won't be used eternally. |
Transmission Monitor's Vibration Isolation Stage for X: preparation (TMS-VISX)
- With a fixed stage.
- TMS = BRT (beam reducing telescope) + GPT (Gouy phase telescope)
|
|
|
|
Links to knowledge
Mechanical design: Mechanical design of TMS Vibration Isolation Stage (by Uraguchi-san)
Ref: design of blade spring for TMS VIS stage (in Japanese) (by Uraguchi-san)
Ref: mechanical model of TMS VIS (in Japanese) (by Uraguchi-san)
Memo: https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=8480
note: https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=8508
メモ: http://gwwiki.icrr.u-tokyo.ac.jp/JGWwiki/KAGRA/subgroup/AOS/TMS-VIS0/2018-09-12
LVDTs
Be careful! The pin assignment in the Dsub shell or the signal phases would be different from the below for #1 and #2, as I needed to once detach the pins when I installed the LVDTs (Akutsu).
http://klog.icrr.u-tokyo.ac.jp/osl/?r=5046: note: LVDT1's coil wires were broken.
http://klog.icrr.u-tokyo.ac.jp/osl/?r=5106: note: LVDT6's coil wires were broken.
Polarity & Calibration Factor
- V: postive means that the LVDT outputs positive counts when TMS-VIS moves upward, and so the calibration factors are set.
- H: postive means that the LVDT outputs positive counts when TMS-VIS moves positive yaw (counter clock wise from top view), and so the calibration factors are set.
Sensor |
Serial# |
polarity |
calibration factor |
LVDT V1 |
#4 |
negative |
-0.149 [um/cnt] |
LVDT V2 |
#5 |
positive |
0.138 [um/cnt] |
LVDT V3 |
#6 |
negative |
-0.135 [um/cnt] |
LVDT H1 |
#1 |
positive |
0.154 [um/cnt] |
LVDT H2 |
#2 |
positive |
0.146 [um/cnt] |
LVDT H3 |
#3 |
positive |
0.150 [um/cnt] |
Actuator coils
Be careful! The pin assignment in the Dsub shell or the signal phases would be different from the below, as I needed to once detach the pins when I installed the coils (Akutsu).
- Tanioka-kun's efforts in 2017
Polarity & Calibration Factor
- V: postive means upward (TMS-VIS moves in upward by inputting positive value to the act coils from MEDM)
- H: positive means plus yaw (TMS-VIS moves in counter clock wise from top view by inputting positive value to the act coils from MEDM)
Actuator |
polarity |
Serial# |
COIL V1 |
positive |
#10 |
COIL V2 |
positive |
#11 |
COIL V3 |
positive |
#12 |
COIL H1 |
negative (obsolete) -> |
#7(obsolete)-> #2 |
COIL H2 |
positive (obsolete)-> |
#8(obsolete) -> #4 |
COIL H3 |
positive (obsolete) -> |
#9(obsolete)-> #5 |
Unfortunately, the actuator coils serial#7, 8, and 9 were broken during the transportation from Mitaka to Xend; their serial number won't be used eternally.
Geophones
Serical# of L-4C |
Vert/Horiz |
Naming of the assembled unit |
Assembler |
404080975 |
Vert |
|
|
404080976 |
Vert |
TMS-VISX: Geo-V2 |
Akutsu |
404080977 |
Vert |
|
|
404080978 |
Vert |
|
|
404084240 |
Vert |
|
|
404084241 |
Vert |
TMS-VISX: Geo-V3 |
Akutsu |
404084242 |
Vert |
TMS-VISX: Geo-V1 |
Fujii -> Akutsu |
2 |
Horiz |
TMS-VISX: Geo-H3 |
Akutsu -> Uraguchi |
3 |
Horiz |
|
|
4 |
Horiz |
TMS-VISX: Geo-H1 |
Akutsu |
5 |
Horiz |
TMS-VISX: Geo-H2 |
Akutsu |
15 |
Horiz |
|
|
16 |
Horiz |
|
|
17 |
Horiz |
|
|
Cabling
- LVDT/Act - (coil wires) - Dsub9M - (Dsub9F - PTFE 2m - Dsub9F) - Dsub9M flange - Flipper cable - Dsub Cable
- Geophone - (MIL C 26482 - PTFE 0.5m - Dsub9M) - (Dsub9F - 1.5m PTFE - Dsub9F) - Dsub9M flange - Flipper cable - Dsub Cable
Task list
Note: some of the tasks can be done in parallel.
Signal Assign
Pin Name |
Resistance |
Equipment |
Assign |
Comment1 |
Comment2 |
Connection |