Differences between revisions 101 and 102

Wide Angle Baffle Cooling Test 2018

Important note about data

Note: some of the tasks can be done in parallel.

Place/install the WAB suspension.
Measure several relative dimensions to get useful information for the future commissioning; concretely speaking:
- What....?
Test the saving mode of the WAB suspension.
Don't forget to replace the damping magnets to SmCo ones.
- What is the requirement to say the damping is sufficient...?
Connect electric cables (with checking) in the IYC chamber.
- 3 photosensors; in each photosensor head, two PDs should be connected parallel. Need to calibrate the response of each sensor head...
- 2 heaters; should be connected parallel??
- 1 coil for actuation.
- 6 thermometers with (extended?) patch cables made of phospher bronze; the extended double twisted pare cables will be delivered on Jan 26
Connect 4 heat links.
Check oplev signals.
Connect cables the outside as well.
Make a realtime model to monitor.
Take interface with Tcam.
Make a plan to do leak check before cooling down.
Don't forget to add some heat links (Cu?) to the top of the suspension...

The PDs and LED are aligned as shown in the below picture.

Photosensor head PD and LED pin assign

The following LEDs and PDs are used; thanks for the information from Fukunaga-kun and Ushiba-kun.

OSEM satellite amp is used to drive.

NOTE: The meaning of color for thermometer cable is
RED = I- , YELLOW = I+ , GREEN = V- , BLACK = V+

P22

P23

Pin Name	Resistance	Equipment	Assign	Comment1	Comment2	Connection
A	75 ohm	Thermometer	V-	Green	Cryocon CH F	○
B	75 ohm	Thermometer	V+	Black		○
C	4 ohm	Coil Mag. Act.	I-		As low resistor line was needed.	○
D	4 ohm	Coil Mag. Act.	I+		As low resistor line was needed.	○
E	75 ohm	PS1 PD	V- (K)			○
F	75 ohm	PS1 PD	V+ (A)			○
G	4 ohm	PS1 LED	I- (K)			○
H	4 ohm	PS1 LED	I+ (A)			○
J	75 ohm	PS2 PD	V- (K)			○
K	75 ohm	PS2 PD	V+ (A)			○
L	4 ohm	PS2 LED	I- (K)			○
M	4 ohm	PS2 LED	I+ (A)			○
N	Blank
P	75 ohm	PS3 PD	V- (K)			○
R	75 ohm	PS3 PD	V+ (A)			○
S	4 ohm	PS3 LED	I- (K)			○
T	4 ohm	PS3 LED	I+ (A)			○
U	75 ohm	Thermometer	I-	Red	Cryocon CH F	○
V	75 ohm	Thermometer	I+	Yellow	Cryocon CH F	○
W	4 ohm	Heater	I-			○
X	4 ohm	Heater	I+			○
Y	Blank

Diagram

Real-time computer: k1???

Diagram

Alignment done with 2 laser-leveler inside the IYC
Regarding the used terms:
- As the baffle is placed along the Y-arm, +Y and -Y refer to both long ends of the baffle toward the Y-end and toward the center area, respectively!
- The same holds true for the horizontal dimension in x-arm direction (+X means toward X-end and -X toward center/PSL)

laser-leveler needs to be close to the -Y main-beam entrance in a height 300 - 400 mm above the optical table
Vertical laser line to be adjusted to the main-beam indication on the optical table and the inner wall of the cryostat
Checked the line by using the slids of the flanges on top the WAB (each slid is ~3.5 mm broad)
For both slids, the laser line is mismatched (not centered) toward -X by ~0.5 mm (@ +Y slid) and ~1 mm (@ -Y slid)

That means that there is probably also a -X offset!

The flanges have a distance of 170 mm which indicates a maximum yaw-tilting of ~0.1 degrees

Note: taking the distances is very hard as the position of the slids is not easy to access

laser-leveler outside the cryostat (but inside IYC) set to give a horizontal line along length side of the baffle
Found a slight mismatch for the outer screw holding the OpLev mirrors in +Y,+X and -Y,+X
Difference is ~1 mm (+Z @ -Y, so -Y-side is higher than +Y-side)
With approx. 500 mm distance between both screws, the maximum pitch is ~0.1 degrees

Took the height of the OpLev mirror screw-holes (@ -Y,+X and -Y,-X) with a vertical ruler and the horizontal line of the laser-leveler outside the cryostat
Measured a difference of 2.5 mm which makes it a roll of 0.55 degrees (radius of baffle ~130 mm); -Y,-X is higher!
Then took the height of baffle-wings which are mounted on the flanges and could not measure any difference (within an error of 0.5 mm)
Hence, only the baffle is slightly rolled within the flanges!

LCGT/subgroup/AOS/WideAngleBuffle (last edited 2018-07-18 15:17:37 by TomotadaAkutsu)

-  ⇤ ← Revision 101 as of 2018-05-10 13:31:59 → 
  Size: 9597
  Editor: TomotadaAkutsu
  Comment:
+   ← Revision 102 as of 2018-05-10 13:32:14 → ⇥
  Size: 9616
  Editor: TomotadaAkutsu
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 9:
- * [[LCGT/subgroup/AOS/WideAngleBuffle/CoilInjectionTime|]]
+ * [[LCGT/subgroup/AOS/WideAngleBuffle/CoilInjectionTime|Coil Injection Time]]