Differences between revisions 31 and 74 (spanning 43 versions)

Wide Angle Baffle Cooling Test 2018

Links to knowledge

Wide Angle Baffle desing review (Obuchi)
Requirements for heat links of WAB (Akutsu)
Temporal information links
Wide Angle Baffle assembly-procedure manual (Zeidler)
Calculations regarding the back-scattering of different Wide Angle Baffle designs (Zeidler)
Personal calc of WAB's stray light noise by Akutsu; due to several uncertain parameters there are several results and no one would know the actual effect!
Heat links positions (by Obuchi) fmkopgehpapgdkcc.png

Task list

Note: some of the tasks can be done in parallel.

Place/install the WAB suspension.
Measure several relative dimensions to get useful information for the future commissioning; concretely speaking:
- What....?
Test the saving mode of the WAB suspension.
Don't forget to replace the damping magnets to SmCo ones.
- What is the requirement to say the damping is sufficient...?
Connect electric cables (with checking) in the IYC chamber.
- 3 photosensors; in each photosensor head, two PDs should be connected parallel. Need to calibrate the response of each sensor head...
- 2 heaters; should be connected parallel??
- 1 coil for actuation.
- 6 thermometers with (extended?) patch cables made of phospher bronze; the extended double twisted pare cables will be delivered on Jan 26
Connect 4 heat links.
Check oplev signals.
Connect cables the outside as well.
Make a realtime model to monitor.
Take interface with Tcam.
Make a plan to do leak check before cooling down.
Don't forget to add some heat links (Cu?) to the top of the suspension...

PIN Assign

Summary of the pin assign of burndy connector inside the cryostat.

NOTE: The meaning of color for thermometer cable is
RED = I- , YELLOW = I+ , GREEN = V- , BLACK = V+

P22

Pin Name	Resistance	Equipment	Assign	Comment1	Comment2	Connection
A	75 ohm	Thermometer	V-	Green	Cryocon CH A	○
B	75 ohm	Thermometer	V+	Black		○
C	4 ohm	Thermometer	I-	Red		○
D	4 ohm	Thermometer	I+	Yellow		○
E	75 ohm	Thermometer	V-	Green	Cryocon CH B	○
F	75 ohm	Thermometer	V+	Black		○
G	4 ohm	Thermometer	I-	Red		○
H	4 ohm	Thermometer	I+	Yellow		○
J	75 ohm	Thermometer	V-	Green	Cryocon CH C	○
K	75 ohm	Thermometer	V+	Black		○
L	4 ohm	Thermometer	I-	Red		○
M	4 ohm	Thermometer	I+	Yellow		○
N	Blank
P	75 ohm	Thermometer	V-	Green	Cryocon CH D	○
R	75 ohm	Thermometer	V+	Black		○
S	4 ohm	Thermometer	I-	Red		○
T	4 ohm	Thermometer	I+	Yellow		○
U	75 ohm	Thermometer	V-	Green	Cryocon CH E	○
V	75 ohm	Thermometer	V+	Black		○
W	4 ohm	Thermometer	I-	Red		○
X	4 ohm	Thermometer	I+	Yellow		○
Y	Blank

P23

Pin Name	Resistance	Equipment	Assign	Comment1	Comment2	Connection
A	75 ohm	Thermometer	V-	Green	Cryocon CH F	×
B	75 ohm	Thermometer	V+	Black		×
C	4 ohm	Thermometer	I-	Red		×
D	4 ohm	Thermometer	I+	Yellow		×
E	75 ohm	PS PD	V-			×
F	75 ohm	PS PD	V+			×
G	4 ohm	PS LED	I-			×
H	4 ohm	PS LED	I+			×
J	75 ohm	PS PD	V-			×
K	75 ohm	PS PD	V+			×
L	4 ohm	PS LED	I-			×
M	4 ohm	PS LED	I+			×
N	Blank
P	75 ohm	PS PD	V-			×
R	75 ohm	PS PD	V+			×
S	4 ohm	PS LED	I-			×
T	4 ohm	PS LED	I+			×
U	75 ohm	CM Act.	I-			×
V	75 ohm	CM Act.	I+			×
W	4 ohm	Heater	I-			○
X	4 ohm	Heater	I+			○
Y	Blank

Diagram

DAQ

Real-time computer: k1???

Slot	Item	Assigned to	S/N
42	<blank>
41	<blank>
40	<blank>
39	<blank>
38	<blank>
37	<blank>
36	<blank>
35	<blank>
34	<blank>
33	<blank>
32	<blank>
31	<blank>
30	<blank>
29	<blank>
28	<blank>
27	<blank>
26	<blank>
25	<blank>
24	<blank>
23	<blank>
22	<blank>
21	<blank>
20	<blank>
19	<blank>
18	<blank>
17	<blank>
16	<blank>
15	<blank>
14	<blank>
13	<blank>
12	AI Chassis	DAC0	SN???
11	AA Chassis	ADC0	SN???
10	<blank>
9	I/O Chassis		SN???
8				<blank>
7				<blank>
6				<blank>
5	<blank>
4	<blank>
3	<blank>
2	<blank>
1	<blank>
0	<blank>

OpLev

Optical lever installed at the +X/-Y side of the IYC
Path-length inside the chamber (viewport to viewport): ~3000 mm

Diagram

WAB Alignment

Alignment done with 2 laser-leveler inside the IYC
Regarding the used terms:

1. As the baffle is placed along the Y-arm, +Y and -Y refer to both long ends of the baffle toward the Y-end and toward the center area, respectively! 2. The same holds true

Yaw

laser-leveler needs to be close to the -Y main-beam entrance in a height 300 - 400 mm above the optical table
Vertical laser line to be adjusted to the main-beam indication on the optical table and the inner wall of the cryostat
Checked the line by using the slids of the flanges on top the WAB (each slid is ~3.5 mm broad)
For both slids, the laser line is mismatched (not centered) toward -X by ~0.5 mm (@ +Y slid) and ~1 mm (@ -Y slid)

That means that there is probably also a -X offset!

The flanges have a distance of 170 mm which indicates a maximum yaw-tilting of ~0.1 degrees

Note: taking the distances is very hard as the position of the slids is not easy to access

Pitch

laser-leveler outside the cryostat (but inside IYC) set to give a horizontal line along length side of the baffle
Found a slight mismatch for the outer screw holding the OpLev mirrors in +Y,+X and -Y,+X
Difference is ~1 mm (+Z @ -Y, so -Y-side is higher than +Y-side)
With approx. 500 mm distance between both screws, the maximum pitch is ~0.1 degrees

Roll

Took the height of the OpLev mirror screw-holes (@ -Y,+X and -Y,-X) with a vertical ruler and the horizontal line of the laser-leveler outside the cryostat
Measured a difference of 2.5 mm which makes it a roll of 0.55 degrees (radius of baffle ~130 mm); -Y,-X is higher!
Then took the height of baffle-wings which are mounted on the flanges and could not measure any difference (within an error of 0.5 mm)
Hence, only the baffle is slightly rolled within the flanges!

LCGT/subgroup/AOS/WideAngleBuffle (last edited 2018-07-18 15:17:37 by TomotadaAkutsu)

-  ⇤ ← Revision 31 as of 2018-01-26 00:33:37 → 
  Size: 2922
  Editor: TomotadaAkutsu
  Comment:
+   ← Revision 74 as of 2018-02-09 15:05:58 → ⇥
  Size: 8479
  Editor: SimonZeidler
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 1:
-= Wide Angle Baffle =
+= Wide Angle Baffle Cooling Test 2018 =
 Line 3:
-<<MonthCalendar>>
+||<<MonthCalendar(,2018,1)>>||<<MonthCalendar(,2018,2)>>||<<MonthCalendar(,2018,3)>>||
-Line 9:
+Line 10:
+ * [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=7588|Wide Angle Baffle assembly-procedure manual (Zeidler)]]
 * [[https://gwdoc.icrr.u-tokyo.ac.jp/cgi-bin/private/DocDB/ShowDocument?docid=4660|Calculations regarding the back-scattering of different Wide Angle Baffle designs (Zeidler)]]
 * [[https://nbviewer.jupyter.org/urls/dl.dropbox.com/s/niycmhy8178ed0y/WAB20170224.ipynb|Personal calc of WAB's stray light noise by Akutsu]]; due to several uncertain parameters there are several results and no one would know the actual effect!
 * Heat links positions (by Obuchi) [[attachment:fmkopgehpapgdkcc.png]]
-Line 19:
+Line 23:
- * Don't forget to replace the damping magnets to SmCo ones; those will be delivered on '''''Jan 26'''''.
+ * Don't forget to replace the damping magnets to SmCo ones.
-Line 32:
+Line 36:
+ * Don't forget to add some heat links (Cu?) to the top of the suspension...
-Line 33:
+Line 38:
+== PIN Assign ==
 * Summary of the pin assign of burndy connector inside the cryostat.

NOTE:
The meaning of color for thermometer cable is <<BR>>
RED = I- , YELLOW = I+ , GREEN = V- , BLACK = V+ 

P22
||Pin Name||Resistance|| Equipment  || Assign || Comment1  || Comment2 || Connection ||
||A||75 ohm|| Thermometer || V- || Green || Cryocon CH A  || ○ ||
||B||75 ohm|| Thermometer || V+ || Black ||  ||  ○ ||
||C||4 ohm|| Thermometer || I- || Red ||  ||  ○ ||
||D||4 ohm|| Thermometer || I+ || Yellow ||  || ○ ||
||E||75 ohm|| Thermometer || V- || Green || Cryocon CH B  ||  ○ ||
||F||75 ohm|| Thermometer || V+ || Black ||  ||  ○ ||
||G||4 ohm|| Thermometer || I- || Red ||  ||  ○ ||
||H||4 ohm|| Thermometer || I+ || Yellow ||  ||  ○ ||
||J||75 ohm|| Thermometer || V- || Green || Cryocon CH C  ||  ○ ||
||K||75 ohm|| Thermometer || V+ || Black ||  ||  ○ ||
||L||4 ohm|| Thermometer || I- || Red ||  ||  ○ ||
||M||4 ohm|| Thermometer || I+ || Yellow ||  ||  ○ ||
||N||Blank|| || || || || ||
||P||75 ohm|| Thermometer || V- || Green || Cryocon CH D  ||  ○ ||
||R||75 ohm|| Thermometer || V+ || Black ||  ||  ○ ||
||S||4 ohm|| Thermometer || I- || Red ||  ||  ○ ||
||T||4 ohm|| Thermometer || I+ || Yellow ||  ||  ○ ||
||U||75 ohm|| Thermometer || V- || Green || Cryocon CH E  ||  ○ ||
||V||75 ohm|| Thermometer || V+ || Black ||  ||  ○ ||
||W||4 ohm|| Thermometer || I- || Red ||  ||  ○ ||
||X||4 ohm|| Thermometer || I+ || Yellow ||  ||  ○ ||
||Y||Blank|| || || || ||　||

P23
||Pin Name||Resistance|| Equipment  || Assign || Comment1  || Comment2 || Connection ||
||A||75 ohm|| Thermometer || V- || Green || Cryocon CH F  || × ||
||B||75 ohm|| Thermometer || V+ || Black ||  || × ||
||C||4 ohm|| Thermometer || I- || Red ||  || × ||
||D||4 ohm|| Thermometer || I+ || Yellow ||  || × ||
||E||75 ohm|| PS PD || V- || ||  || × ||
||F||75 ohm|| PS PD || V+ || ||  || × ||
||G||4 ohm|| PS LED || I- || ||  || × ||
||H||4 ohm|| PS LED || I+ || ||  || × ||
||J||75 ohm|| PS PD || V- || ||  || × ||
||K||75 ohm|| PS PD || V+ || ||  || × ||
||L||4 ohm|| PS LED || I- || ||  || × ||
||M||4 ohm|| PS LED || I+ || ||  || × ||
||N||Blank|| || || || || ||
||P||75 ohm|| PS PD || V- || ||  || × ||
||R||75 ohm|| PS PD || V+ || ||  || × ||
||S||4 ohm|| PS LED || I- || ||  || × ||
||T||4 ohm|| PS LED || I+ || ||  || × ||
||U||75 ohm|| CM Act. || I- || ||  || × ||
||V||75 ohm|| CM Act. || I+ || ||  || × ||
||W||4 ohm|| Heater || I- || ||  || ○ ||
||X||4 ohm|| Heater || I+ || ||  || ○ ||
||Y||Blank|| || || || || ||

{{attachment:burndy_cryostat.png |  Diagram|width="300" }}
-Line 81:
+Line 144:
+== OpLev ==

 * Optical lever installed at the +X/-Y side of the IYC
 * Path-length inside the chamber (viewport to viewport): ~3000 mm

{{attachment:ETMchamber_WAB_oplev_beams3.PNG| Diagram|width="500"}}

== WAB Alignment ==

 * Alignment done with 2 laser-leveler inside the IYC
 * Regarding the used terms:
1. As the baffle is placed along the Y-arm, +Y and -Y refer to both long ends of the baffle toward the Y-end and toward the center area, respectively!
2. The same holds true

=== Yaw ===

 * laser-leveler needs to be close to the -Y main-beam entrance in a height 300 - 400 mm above the optical table
 * Vertical laser line to be adjusted to the main-beam indication on the optical table and the inner wall of the cryostat
 * Checked the line by using the slids of the flanges on top the WAB (each slid is ~3.5 mm broad)
 * For both slids, the laser line is mismatched (not centered) toward -X by ~0.5 mm (@ +Y slid) and ~1 mm (@ -Y slid)
That means that there is probably also a -X offset!
 * The flanges have a distance of 170 mm which indicates a maximum yaw-tilting of ~0.1 degrees

'''Note:''' taking the distances is very hard as the position of the slids is not easy to access

=== Pitch ===

 * laser-leveler outside the cryostat (but inside IYC) set to give a horizontal line along length side of the baffle
 * Found a slight mismatch for the outer screw holding the OpLev mirrors in +Y,+X and -Y,+X
 * Difference is ~1 mm (+Z @ -Y, so -Y-side is higher than +Y-side)
 * With approx. 500 mm distance between both screws, the maximum pitch is ~0.1 degrees

=== Roll ===

 * Took the height of the OpLev mirror screw-holes (@ -Y,+X and -Y,-X) with a vertical ruler and the horizontal line of the laser-leveler outside the cryostat
 * Measured a difference of 2.5 mm which makes it a roll of 0.55 degrees (radius of baffle ~130 mm); -Y,-X is higher!
 * Then took the height of baffle-wings which are mounted on the flanges and could not measure any difference (within an error of 0.5 mm)
 * Hence, only the baffle is slightly rolled within the flanges!