Differences between revisions 320 and 366 (spanning 46 versions)

KAGRA Commissioning Wiki

Task list

Schedule

2017/3/26 updated KAGRA/Commissioning/Commissioning_schedule_20180327.png

Working people assignment

*: responsible person

Meetings

Morning meeting

Date and time: Every weekday, 9AM
Location: Control room, or eZuce

2018/4/2(Fri.)

* Remote participants by eZuce: Enomoto

Report of work (*:responsible person)

* ETMX: *Ushiba

Confirmed the returned beam at REFL
Calibration of OpLev is on going (mostly finished)
Start Characterization

* ETMY: *Miyamoto

Damping is working well. Less than 2urad RMS.

* BS: *Enomoto

Two different problems identified
- Apparent bi-stability of OpLev -> Replaced the satellite box -> Gone
- Glitches -> Looks like the same problem as ETMY: DAC output goes to zero

* PCal: Binhua

Aligned the beam within the PCal module

* ETMX camera: Yokozawa

Ready but not installed

* TMS: no one to report

Work plan (*:responsible person)

* ETMX: *Ushiba, Miyamoto

Start Characterization

* BS: Enomoto

Check the glitches over the weekend

* PCal: Binhua

Measure PCal transfer functions

* ETMX Camera: Yokozawa

Set up necessary components to take high frame rate pictures

Laser hazard

* [AM]

IR: SR2-3 line, Xend 1F, Yend 1F
Green: PR2, Xend 1F

* [PM]

IR: SR2-3 line, Xend 1F, Yend 1F
Green: PR2, Xend 1F

* [night]

IR: SR2-3 line, Xend 1F, Yend 1F
Green: PR2, Xend 1F

2017/3/30(Fri.)

Remote participants by eZuce: None

Report of work (*:responsible person)

ETMX: *Takahashi, Ishizaki, Sato, Okutomi, Tomaru, Takahashi, Ushiba, Miyamoto, Enomoto, Nagano
- Mirror will be aligned with beam today to REFL. But IR and green are not overlapped well.
- Oplev is placed but not calibrated.
- LVDT of BF seems to be something wrong. It could be satellite box.
BS: *Enomoto, Enzo
- Hightower coil driver and satellite box was replaced. Satellite box was something wrong. Oplev jump disappeared. But still glitch remains.
- Hyper threading should be off.
BRT: Nagano
- TMS was seen and aligned to QPD.

Work plan (*:responsible person)

ETMX: *Ushiba, Takahashi
- Beam will be aligned more precisely with aligned IR.
CAL: *Yamamoto
- CAL model is tested using iMC.
Camera: Yokozawa
- EX camera takes every one hour. It is necessary 1 sec picture in the weekend.

Laser hazard

[AM]
- IR: SR2-3 line, Xend 1F, Yend 1F
- Green: PR2, Xend 1F
[PM]
- IR: SR2-3 line, Xend 1F, Yend 1F
- Green: PR2, Xend 1F
[night]
- IR: SR2-3 line, Xend 1F, Yend 1F
- Green: PR2, Xend 1F

Weekly

week of 3/26
- 3/26 Pcal will start, and all the 1st floor of Y-end will be laser hazard area.
- Connection of cable at ETMX and starting control.
- Rough alignment of ETMX using IR.
  - 3/27 EX PD will be removed.: *Yokozawa
week of 4/2
- ETMY damping.
- Rough alignment of ETMX using IR, and control MICH if can.
week of 4/9
- Closing EXC

Issues

BS: DAC had some glitches but if DAC is off, no glitch was found.

KAGRA/Commissioning/DailyWork << < 2024 / 7 > >>
Mon	Tue	Wed	Thu	Fri	Sat	Sun
1	2	3	4	5	6	7
8	9	10	11	12	13	14
15	16	17	18	19	20	21
22	23	24	25	26	27	28
29	30	31

Weekly meeting

Date and time: Every Tuesday, 11AM
Location: Meeting room at Hokubukaikan, or eZuce, Polycom

No.	Date	Agenda	Schedule	Minute	Files

24	2018/3/27	Agenda	Schedule	Minute
23	2018/3/20	Agenda	Schedule	Minute
22	2018/3/13	Agenda	Schedule	Minute
21	2018/3/6	Agenda	Schedule	Minute
20	2018/2/27	Agenda	Schedule	Minute
19	2018/2/20	Agenda	Schedule	Minute
18	2018/2/13	Agenda	Schedule	Minute
17	2018/2/6	Agenda	Schedule	Minute
16	2018/1/30	Agenda	Schedule	Minute
15	2018/1/23	Agenda	Schedule	Minute
14	2018/1/16	Agenda	Schedule	Minute
13	2018/1/9	Agenda	Schedule	Minute
12	2017/12/19	Agenda	Schedule	Minute
11	2017/12/12	Agenda	Schedule	Minute
10	2017/11/28	Agenda	Schedule	Minute
9	2017/11/14	Agenda	Schedule	Minute
8	2017/11/7	Agenda	Schedule	Minute
7	2017/10/31	Agenda		Minute	G1707278-v4
6	2017/10/24	Agenda		Minute	G1707278-v3
5	2017/10/17	Agenda		Minute	G1707278-v2 G1707298 G1707300
4	2017/10/10			Minute	G1707278-v1
3	2017/10/3	Agenda		Minute	Commissioning plan for phase1
2	2017/9/26	Agenda		Minute	Commissioning plan for phase1
1	2017/9/19				Commissioning plan for phase1

Other meetings

Meeting for pump down test at Center are (Minute, Check list)
Meeting for pump down and cooling at ETMY3 (Minute, Check list)
Meeting for pump down and cooling at ETMY2 (Minute, Check list)
Meeting for pump down and cooling at ETMY1 (Minute, Check list)
Meeting for pump down at ETMY (Minute, schedule)
Meeting for closing ETY (Minute)
Meeting about PR2 pitch misalignment (Minute)
Commissioning Workshop 2017

Documents

Commissioning plan for Phase1

Communication tools

KAGRA commissioning Mailing List
wiki
- Task list (Phase base, stage base)
- Meetings (morning, weekly)
Scheduler
Task assignment list (example)
klog
Issue tracker: Bugzilla (currently site internal only)

for New members

Joining commissioning Mailing List

-  ⇤ ← Revision 320 as of 2018-03-01 09:30:38 → 
  Size: 9633
  Editor: OsamuMiyakawa
  Comment:
+   ← Revision 366 as of 2018-04-02 10:45:59 → ⇥
  Size: 11736
  Editor: YoichiAso
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 11:
-/2/26 updated
{{attachment:KAGRA/Commissioning/Commissioning_schedule_20180227.png||width=1200}}
+/3/26 updated
{{attachment:KAGRA/Commissioning/Commissioning_schedule_20180327.png||width=1200}}
 Line 18:
- * Beam leading to REFP port
  * *Enomoto
-Line 53:
+Line 50:
-/3/1(Thur.)
+=== 2018/4/2(Fri.) ===

* Remote participants by eZuce: Enomoto

==== Report of work (*:responsible person) ====
* ETMX: *Ushiba
 * Confirmed the returned beam at REFL
 * Calibration of OpLev is on going (mostly finished)
 * Start Characterization 

* ETMY: *Miyamoto
  * Damping is working well. Less than 2urad RMS.

* BS: *Enomoto
 * Two different problems identified
  * Apparent bi-stability of OpLev  -> Replaced the satellite box -> Gone
  * Glitches -> Looks like the same problem as ETMY: DAC output goes to zero

* PCal: Binhua
 * Aligned the beam within the PCal module
 
* ETMX camera: Yokozawa
 * Ready but not installed 

* TMS: no one to report

==== Work plan (*:responsible person) ====

* ETMX: *Ushiba, Miyamoto
  * Start Characterization 

* BS: Enomoto
 * Check the glitches over the weekend

* PCal: Binhua
  * Measure PCal transfer functions

* ETMX Camera: Yokozawa
  * Set up necessary components to take high frame rate pictures

==== Laser hazard ====
* [AM]
  * IR: SR2-3 line, Xend 1F, Yend 1F
  * Green: PR2, Xend 1F
* [PM]
  * IR: SR2-3 line, Xend 1F, Yend 1F
  * Green: PR2, Xend 1F

* [night]
  * IR: SR2-3 line, Xend 1F, Yend 1F
  * Green: PR2, Xend 1F


2017/3/30(Fri.)
-Line 58:
+Line 107:
- * Report of work (*:responsible person)

  * Height change of PRs: Tomaru, *Aso, Takahashi, Ohishi, Miyo
   * We opened the PR2 and PR3 chamber and we confirmed that the height of keystone and mirror of PR2 and PR3 were not at the wrong point.
   * PR2 was within ~1mm range and PR3 was ~5mm range from the center line. The height of RP3 was changed a bit by fishing rod, and we did not change PR2.
   * Fishing rods worked well and still were within the range.
   * LVDT seemed to have jumps several times in the past, so absolute position of LVDT is not trustable.
    * Recorded the current height and current value.
   * It means that the beam changed upstream PR like IMMT, or MC.
   * We absolutely need monitors to check beam position at all the mirrors.


  * IOO: kokeyama
   * A good IO chassis changed and everything seems to be OK now.

  * AOS:
   * Lasers of oplev will can be dying soon.
    * The lifetime is about 100000h.


  * Camara: Yokozawa, Inouse
   * We tried to see BS using Tcam at IXC, but we could not see the BS even with an illuminator. This may be because of the limit of area of viewport on the gate valve.

  * CRY: mirror temperature ~94K.


 * Work plan (*:responsible person)

  * Alignment: 
   * IMMT and MC will be aligned to center PRs.

 * Laser hazard: AM: PSL, PM: Upstream SR2-3 line, and Y-end.

 * Weekly
  * Week of 2/26
   * ETMY tuninng.
   * Beam alignment to REFL port.
   * 2/28: Height change for PRs

  * week of 3/5
   * IYC door will be closed.
   * Exchanging items and cleaning inside the PR2 chamber

  * week of 3/12
   * TMS installation at ETMY.
   * Connecting ducts at the corner area.

  * week of 3/19
   * Vacuum test at at the corner area.
   * TMS alignment using green light at ETMY.


 * Issues
+==== Report of work (*:responsible person) ====

 * ETMX: *Takahashi, Ishizaki, Sato, Okutomi, Tomaru, Takahashi, Ushiba, Miyamoto, Enomoto, Nagano
  * Mirror will be aligned with beam today to REFL. But IR and green are not overlapped well.
  * Oplev is placed but not calibrated.
  * LVDT of BF seems to be something wrong. It could be satellite box.

 * BS: *Enomoto, Enzo
  * Hightower coil driver and satellite box was replaced. Satellite box was something wrong. Oplev jump disappeared. But still glitch remains.
  * Hyper threading should be off.

 * BRT: Nagano
  * TMS was seen and aligned to QPD.


 * 

==== Work plan (*:responsible person) ====

 * ETMX: *Ushiba, Takahashi
  * Beam will be aligned more precisely with aligned IR.

 * CAL: *Yamamoto
  * CAL model is tested using iMC.

 * Camera: Yokozawa
  * EX camera takes every one hour. It is necessary 1 sec picture in the weekend.


==== Laser hazard ====
 * [AM]
  * IR: SR2-3 line, Xend 1F, Yend 1F
  * Green: PR2, Xend 1F
 * [PM]
  * IR: SR2-3 line, Xend 1F, Yend 1F
  * Green: PR2, Xend 1F

 * [night]
  * IR: SR2-3 line, Xend 1F, Yend 1F
  * Green: PR2, Xend 1F

==== Weekly ====

 * week of 3/26
  * 3/26 Pcal will start, and all the 1st floor of Y-end will be laser hazard area.
  * Connection of cable at ETMX and starting control.
  * Rough alignment of ETMX using IR.
   * 3/27 EX PD will be removed.: *Yokozawa

 * week of 4/2
  * ETMY damping.
  * Rough alignment of ETMX using IR, and control MICH if can.

 * week of 4/9
  * Closing EXC

==== Issues ====

 * BS: DAC had some glitches but if DAC is off, no glitch was found.
-Line 117:
+Line 173:
-==== Weekly meeting ====
+=== Weekly meeting ===
-Line 122:
+Line 178:
+||24||2018/3/27||[[KAGRA/Commissioning/Weekly/20180327/Agenda|Agenda]]||[[attachment:KAGRA/Commissioning/Schedule/Commissioning_schedule_20180327.xlsx|Schedule]]||[[KAGRA/Commissioning/Weekly/20180327/Minute|Minute]]|| ||
||23||2018/3/20||[[KAGRA/Commissioning/Weekly/20180320/Agenda|Agenda]]||[[attachment:KAGRA/Commissioning/Schedule/Commissioning_schedule_20180320.xlsx|Schedule]]||[[KAGRA/Commissioning/Weekly/20180320/Minute|Minute]]|| ||
||22||2018/3/13||[[KAGRA/Commissioning/Weekly/20180313/Agenda|Agenda]]||[[attachment:KAGRA/Commissioning/Schedule/Commissioning_schedule_20180313.xlsx|Schedule]]||[[KAGRA/Commissioning/Weekly/20180313/Minute|Minute]]|| ||
||21||2018/3/6||[[KAGRA/Commissioning/Weekly/20180306/Agenda|Agenda]]||[[attachment:KAGRA/Commissioning/Schedule/Commissioning_schedule_20180306.xlsx|Schedule]]||[[KAGRA/Commissioning/Weekly/20180306/Minute|Minute]]|| ||
-Line 145:
+Line 205:
+ * Meeting for pump down test at Center are ([[/Meetings/Others/20180314|Minute]], [[KAGRA/Commissioning/Phase1/Task/CheckList/20180307_VacuumCenter#preview|Check list]])

KAGRA/Commissioning/DailyWork << < 2024 / 7 > >>
Mon	Tue	Wed	Thu	Fri	Sat	Sun
1	2	3	4	5	6	7
8	9	10	11	12	13	14
15	16	17	18	19	20	21
22	23	24	25	26	27	28
29	30	31

KAGRA/Commissioning/DailyWork << < 2024 / 7 > >>
Mon	Tue	Wed	Thu	Fri	Sat	Sun
1	2	3	4	5	6	7
8	9	10	11	12	13	14
15	16	17	18	19	20	21
22	23	24	25	26	27	28
29	30	31

KAGRA Commissioning Wiki

Task list

Schedule

Working people assignment

Emergency contact person for subsystem

Meetings

Morning meeting

2018/4/2(Fri.)

Report of work (*:responsible person)

Work plan (*:responsible person)

Laser hazard

Report of work (*:responsible person)

Work plan (*:responsible person)

Laser hazard

Weekly

Issues

Weekly meeting

Other meetings

Documents

Communication tools

for New members

KAGRA/Commissioning/DailyWork << < 2024 / 7 > >>
Mon	Tue	Wed	Thu	Fri	Sat	Sun
1	2	3	4	5	6	7
8	9	10	11	12	13	14
15	16	17	18	19	20	21
22	23	24	25	26	27	28
29	30	31