Differences between revisions 320 and 401 (spanning 81 versions)

KAGRA Commissioning Wiki

Task list

Schedule

2017/4/17 updated KAGRA/Commissioning/Commissioning_schedule_20180417.png

Working people assignment

*: responsible person

Meetings

Morning meeting

Date and time: Every weekday, 9AM
Location: Control room, or eZuce

2018/4/26(Thur.)

* Remote participants by eZuce: None

Report of work (*:responsible person)

IFO: *Izumi, Enomoto + many
- Michelson lock lasted longer than 2 and half hours!
- Alignment control from IFO to ETMX was implemented by dithering ETMX.
- PR3 alignment was implemented by baffle signal.
- ETMX damping might be a cause of lock lost.
- ETMY yaw damping inclease pitch motion by coupling. It will be improved today.(Ushiba)
- BS oplev is fed back to not only TM but also IM. (Arai)
WAB: *Akutsu
- Heat consumption is estimated well. 10ppm produce 4W and it will be absorbed by WAB and now it is simulated by heater.
- Equilibrium temperature was 21K.
- Damping became to strong in low temperature.
Wire of RM was broken on SR3 during tightening clamp.
CAL: *Yamamoto
- line injection is being tested.

Work plan (*:responsible person)

IFO: *Izumi, Enomoto, Nakano + many
- Measurement without locking morning, measurement with locking in the afternoon.

Laser hazard

[AM]
- IR: Upstream SR2-3 line, Xend 1F, Yend 1F
- Green: PR2, Xend 1F
[PM]
- IR: Upstream SR2-3 line, Xend 1F, Yend 1F
- Green: PR2, Xend 1F
[night]
- IR: Upstream SR2-3 line, Xend 1F, Yend 1F
- Green: PR2, Xend 1F

Weekly

week of 4/23
- Michelson control.
- 4/28 Operation start

Issues

PR2 had a jump caused by a DAC glitch once a day. Sampling rate will be lowered?
PR3 also had jumps caused by DAC glitches.

KAGRA/Commissioning/DailyWork << < 2024 / 7 > >>
Mon	Tue	Wed	Thu	Fri	Sat	Sun
1	2	3	4	5	6	7
8	9	10	11	12	13	14
15	16	17	18	19	20	21
22	23	24	25	26	27	28
29	30	31

Weekly meeting

Date and time: Every Tuesday, 11AM
Location: Meeting room at Hokubukaikan, or eZuce, Polycom

No.	Date	Agenda	Schedule	Minute	Files

27	2018/4/17	Agenda	Schedule	Minute
26	2018/4/10	Agenda	Schedule	Minute
25	2018/4/3	Agenda	Schedule	Minute
24	2018/3/27	Agenda	Schedule	Minute
23	2018/3/20	Agenda	Schedule	Minute
22	2018/3/13	Agenda	Schedule	Minute
21	2018/3/6	Agenda	Schedule	Minute
20	2018/2/27	Agenda	Schedule	Minute
19	2018/2/20	Agenda	Schedule	Minute
18	2018/2/13	Agenda	Schedule	Minute
17	2018/2/6	Agenda	Schedule	Minute
16	2018/1/30	Agenda	Schedule	Minute
15	2018/1/23	Agenda	Schedule	Minute
14	2018/1/16	Agenda	Schedule	Minute
13	2018/1/9	Agenda	Schedule	Minute
12	2017/12/19	Agenda	Schedule	Minute
11	2017/12/12	Agenda	Schedule	Minute
10	2017/11/28	Agenda	Schedule	Minute
9	2017/11/14	Agenda	Schedule	Minute
8	2017/11/7	Agenda	Schedule	Minute
7	2017/10/31	Agenda		Minute	G1707278-v4
6	2017/10/24	Agenda		Minute	G1707278-v3
5	2017/10/17	Agenda		Minute	G1707278-v2 G1707298 G1707300
4	2017/10/10			Minute	G1707278-v1
3	2017/10/3	Agenda		Minute	Commissioning plan for phase1
2	2017/9/26	Agenda		Minute	Commissioning plan for phase1
1	2017/9/19				Commissioning plan for phase1

Other meetings

Meeting for pump down test at ETMX 2 (Minute, Check list)
Meeting for pump down test at ETMX 1 (Minute, Check list)
Meeting for pump down test at Center are (Minute, Check list)
Meeting for pump down and cooling at ETMY3 (Minute, Check list)
Meeting for pump down and cooling at ETMY2 (Minute, Check list)
Meeting for pump down and cooling at ETMY1 (Minute, Check list)
Meeting for pump down at ETMY (Minute, schedule)
Meeting for closing ETY (Minute)
Meeting about PR2 pitch misalignment (Minute)
Commissioning Workshop 2017

Documents

Commissioning plan for Phase1

Communication tools

KAGRA commissioning Mailing List
wiki
- Task list (Phase base, stage base)
- Meetings (morning, weekly)
Scheduler
Task assignment list (example)
klog
Issue tracker: Bugzilla (currently site internal only)

for New members

Joining commissioning Mailing List

-  ⇤ ← Revision 320 as of 2018-03-01 09:30:38 → 
  Size: 9633
  Editor: OsamuMiyakawa
  Comment:
+   ← Revision 401 as of 2018-04-27 09:19:02 → ⇥
  Size: 11015
  Editor: OsamuMiyakawa
  Comment:
-Deletions are marked like this.
+Additions are marked like this.
 Line 11:
-/2/26 updated
{{attachment:KAGRA/Commissioning/Commissioning_schedule_20180227.png||width=1200}}
+/4/17 updated
{{attachment:KAGRA/Commissioning/Commissioning_schedule_20180417.png||width=1200}}
 Line 18:
- * Beam leading to REFP port
  * *Enomoto
-Line 27:
+Line 24:
- * Laser, Ref''''''Cav, IMC: 苔山、中野
 * IMMT: 大石
 * VIS
  * Type Bp: 正田、三代
  * Type B: Mark
  * Type A: 奥富、宮本
 * Pico''''''Motor: 三代
 * Digital: 山本、宮川
 * 回路: 上泉、霜出
 * DC電源関連: 宮川
 * AC電源関連: 粟井
 * 水漏れなど: 古田、早河
-Line 53:
+Line 39:
+=== 2018/4/26(Thur.) ===
-Line 54:
+Line 41:
-/3/1(Thur.)
+* Remote participants by eZuce: None
-Line 56:
+Line 43:
- * Remote participants by eZuce: None
+==== Report of work (*:responsible person) ====
-Line 58:
+Line 45:
- * Report of work (*:responsible person)
+ * IFO: *Izumi, Enomoto + many
  * Michelson lock lasted longer than 2 and half hours!
  * Alignment control from IFO to ETMX was implemented by dithering ETMX.
  * PR3 alignment was implemented by baffle signal.
  * ETMX damping might be a cause of lock lost.
  * ETMY yaw damping inclease pitch motion by coupling. It will be improved today.(Ushiba)
  * BS oplev is fed back to not only TM but also IM. (Arai)
-Line 60:
+Line 53:
-  * Height change of PRs: Tomaru, *Aso, Takahashi, Ohishi, Miyo
   * We opened the PR2 and PR3 chamber and we confirmed that the height of keystone and mirror of PR2 and PR3 were not at the wrong point.
   * PR2 was within ~1mm range and PR3 was ~5mm range from the center line. The height of RP3 was changed a bit by fishing rod, and we did not change PR2.
   * Fishing rods worked well and still were within the range.
   * LVDT seemed to have jumps several times in the past, so absolute position of LVDT is not trustable.
    * Recorded the current height and current value.
   * It means that the beam changed upstream PR like IMMT, or MC.
   * We absolutely need monitors to check beam position at all the mirrors.
+ * WAB: *Akutsu
  * Heat consumption is estimated well. 10ppm produce 4W and it will be absorbed by WAB and now it is simulated by heater.
  * Equilibrium temperature was 21K.
  * Damping became to strong in low temperature.

 * Wire of RM was broken on SR3 during tightening clamp.

 * CAL: *Yamamoto
  * line injection is being tested.
-Line 70:
+Line 64:
-  * IOO: kokeyama
   * A good IO chassis changed and everything seems to be OK now.
-Line 73:
+Line 65:
-  * AOS:
   * Lasers of oplev will can be dying soon.
    * The lifetime is about 100000h.
+==== Work plan (*:responsible person) ====

 * IFO: *Izumi, Enomoto, Nakano + many
  * Measurement without locking morning, measurement with locking in the afternoon.

 *
-Line 78:
+Line 73:
-  * Camara: Yokozawa, Inouse
   * We tried to see BS using Tcam at IXC, but we could not see the BS even with an illuminator. This may be because of the limit of area of viewport on the gate valve.
+==== Laser hazard ====
 * [AM]
  * IR: Upstream SR2-3 line, Xend 1F, Yend 1F
  * Green: PR2, Xend 1F
 * [PM]
  * IR: Upstream SR2-3 line, Xend 1F, Yend 1F
  * Green: PR2, Xend 1F
 Line 81:
-  * CRY: mirror temperature ~94K.
+ * [night]
  * IR: Upstream SR2-3 line, Xend 1F, Yend 1F
  * Green: PR2, Xend 1F
-Line 84:
+Line 86:
- * Work plan (*:responsible person)
+==== Weekly ====
-Line 86:
+Line 88:
-  * Alignment: 
   * IMMT and MC will be aligned to center PRs.
+ * week of 4/23
  * Michelson control.
  * 4/28 Operation start
-Line 89:
+Line 92:
- * Laser hazard: AM: PSL, PM: Upstream SR2-3 line, and Y-end.
+==== Issues ====
-Line 91:
+Line 94:
- * Weekly
  * Week of 2/26
   * ETMY tuninng.
   * Beam alignment to REFL port.
   * 2/28: Height change for PRs
+  * PR2 had a jump caused by a DAC glitch once a day. Sampling rate will be lowered?
  * PR3 also had jumps caused by DAC glitches.
 Line 97:
-  * week of 3/5
   * IYC door will be closed.
   * Exchanging items and cleaning inside the PR2 chamber

  * week of 3/12
   * TMS installation at ETMY.
   * Connecting ducts at the corner area.

  * week of 3/19
   * Vacuum test at at the corner area.
   * TMS alignment using green light at ETMY.


 * Issues
-Line 117:
+Line 103:
-==== Weekly meeting ====
+=== Weekly meeting ===
-Line 122:
+Line 108:
+||27||2018/4/17||[[KAGRA/Commissioning/Weekly/20180417/Agenda|Agenda]]||[[attachment:KAGRA/Commissioning/Schedule/Commissioning_schedule_20180417.xlsx|Schedule]]||[[KAGRA/Commissioning/Weekly/20180417/Minute|Minute]]|| ||
||26||2018/4/10||[[KAGRA/Commissioning/Weekly/20180410/Agenda|Agenda]]||[[attachment:KAGRA/Commissioning/Schedule/Commissioning_schedule_20180410.xlsx|Schedule]]||[[KAGRA/Commissioning/Weekly/20180410/Minute|Minute]]|| ||
||25||2018/4/3||[[KAGRA/Commissioning/Weekly/20180403/Agenda|Agenda]]||[[attachment:KAGRA/Commissioning/Schedule/Commissioning_schedule_20180403.xlsx|Schedule]]||[[KAGRA/Commissioning/Weekly/20180403/Minute|Minute]]|| ||
||24||2018/3/27||[[KAGRA/Commissioning/Weekly/20180327/Agenda|Agenda]]||[[attachment:KAGRA/Commissioning/Schedule/Commissioning_schedule_20180327.xlsx|Schedule]]||[[KAGRA/Commissioning/Weekly/20180327/Minute|Minute]]|| ||
||23||2018/3/20||[[KAGRA/Commissioning/Weekly/20180320/Agenda|Agenda]]||[[attachment:KAGRA/Commissioning/Schedule/Commissioning_schedule_20180320.xlsx|Schedule]]||[[KAGRA/Commissioning/Weekly/20180320/Minute|Minute]]|| ||
||22||2018/3/13||[[KAGRA/Commissioning/Weekly/20180313/Agenda|Agenda]]||[[attachment:KAGRA/Commissioning/Schedule/Commissioning_schedule_20180313.xlsx|Schedule]]||[[KAGRA/Commissioning/Weekly/20180313/Minute|Minute]]|| ||
||21||2018/3/6||[[KAGRA/Commissioning/Weekly/20180306/Agenda|Agenda]]||[[attachment:KAGRA/Commissioning/Schedule/Commissioning_schedule_20180306.xlsx|Schedule]]||[[KAGRA/Commissioning/Weekly/20180306/Minute|Minute]]|| ||
-Line 145:
+Line 138:
+ * Meeting for pump down test at ETMX 2 ([[/Meetings/Others/20180411|Minute]], [[KAGRA/Commissioning/Phase1/Task/CheckList/20180307_VacuumETMX|Check list]])
 * Meeting for pump down test at ETMX 1 ([[/Meetings/Others/20180405|Minute]], [[KAGRA/Commissioning/Phase1/Task/CheckList/20180307_VacuumETMX|Check list]])
 * Meeting for pump down test at Center are ([[/Meetings/Others/20180314|Minute]], [[KAGRA/Commissioning/Phase1/Task/CheckList/20180307_VacuumCenter|Check list]])

KAGRA/Commissioning/DailyWork << < 2024 / 7 > >>
Mon	Tue	Wed	Thu	Fri	Sat	Sun
1	2	3	4	5	6	7
8	9	10	11	12	13	14
15	16	17	18	19	20	21
22	23	24	25	26	27	28
29	30	31

KAGRA/Commissioning/DailyWork << < 2024 / 7 > >>
Mon	Tue	Wed	Thu	Fri	Sat	Sun
1	2	3	4	5	6	7
8	9	10	11	12	13	14
15	16	17	18	19	20	21
22	23	24	25	26	27	28
29	30	31

KAGRA Commissioning Wiki

Task list

Schedule

Working people assignment

Emergency contact person for subsystem

Meetings

Morning meeting

2018/4/26(Thur.)

Report of work (*:responsible person)

Work plan (*:responsible person)

Laser hazard

Weekly

Issues

Weekly meeting

Other meetings

Documents

Communication tools

for New members

KAGRA/Commissioning/DailyWork << < 2024 / 7 > >>
Mon	Tue	Wed	Thu	Fri	Sat	Sun
1	2	3	4	5	6	7
8	9	10	11	12	13	14
15	16	17	18	19	20	21
22	23	24	25	26	27	28
29	30	31